background image

B

L A C K B O A R D

  ( W R 5 0 0 0 )   R

E A D E R

  I

N S T A L L A T I O N

  G

U I D E

403-003-000 R

EV

 A

 

1-7

The reader must be configured by the administrator to operate in Wiegand mode. In addition to the wiring 
shown above, the reader can also be connected to a network using the RJ-45 connector. This provides a 
means of getting software updates for the Android OS.

Attendance Reader

When using the WR5000 as an attendance reader, the device must be connected to a network.

The WR5000 can be powered using an external power supply, or a Power Over Ethernet (POE) switch. If 
using an external power supply, the power supply must have a regulated output of +12 Volts DC. If using 
POE, a CAT-5 cable must be connected between the POE switch and the RJ-45 connector on the WR5000 
(cable length must not exceed 100 meters).

WARNING

: When using a POE switch to power the WR5000, both the POE switch and 

WR5000 must be installed within the same building or structure.

When using an external supply, wire the reader as shown in 

Table 1-4:

Table 1-3: Wiegand Connection Points

WR5000

Terminal Block

Signal Name

Third-Party Controller connections

TB1-1

V+

Connect to regulated Power Supply (+6V to +24V)

TB1-2

GND

Connect to Ground

TB1-3

D0/DAT

Connect to Wiegand D0 input

TB1-4

D1/CLK

Connect to Wiegand D1 input

TB2-1

GLED

Connect to Green LED output

TB2-2

RLED

Connect to Red LED output

TB2-3

BEEPER

Connect to Beeper output

TB2-4

TAMPER

Connect to Tamper Input

Table 1-4: Power Supply Wiring

WR5000

Terminal Block

Signal Name

External Power supply

TB1-1

V+

Connect to regulated Power Supply (+6V to +24V)

TB1-2

GND

Connect to Ground

Summary of Contents for WR5000














Reviews: