background image

B

L A C K B O A R D

  ( W R 5 0 0 0 )   R

E A D E R

  I

N S T A L L A T I O N

  G

U I D E

403-003-000 R

EV

 A

 

1-3

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the 
following two conditions: (1) this device may not cause interference, and (2) this device must accept any 
interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de 
licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de 
brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le 
brouillage est susceptible d’en compromettre le fonctionnement.

Contains:

Contient des IC: 9049A-ITCOQ410S and 7922A-2005                            

Australia and New Zealand Class A statement

Attention: This is a Class A product. In a domestic environment this product may cause radio interference 
in which case the user may be required to take adequate measures.

Radiation Exposure Statement

This equipment complies with radiation exposure limits set forth for uncontrolled environment. The 
antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm 
from all persons and must not be collocated or operating in conjunction with any other antenna or 
transmitter.

Déclaration d'exposition aux radiations

Cet appareil se conforme aux limites d'exposition aux rayonnements pour un environnement non contrôlé. 
L'antenne (s) qui est utilisé pour cet émetteur doit être installé pour produire une distance de séparation 
d'au moins 20 cm de toutes personnes et ne doit pas être installé à proximité ou utilisé en conjonction avec 
une autre antenne ou émetteur.

IC: 9049A-ITCOQ410S

Intrinsyc Open-Q 410 System-On-Module

IC: 7922A-2005

Cypress Semiconductor Bluetooth Low-Energy Module (CYBLE-222014-01)

Summary of Contents for WR5000














Reviews: