background image

BLACKMER POWER PUMPS 

960229

 

INSTRUCTIONS NO. 102-A00 

INSTALLATION OPERATION AND MAINTENANCE INSTRUCTIONS 

MODELS: HXL6G, HXL8G, HXLJ8G, HXL10E 

Section 

Effective 

Replaces 

102 
Jun 2020 
Jan 2014 
 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

TABLE OF CONTENTS                                       Page 

PUMP DATA

 

 

Technical Data ........................................................... 2 

 

Initial Pump Start Up Information................................ 2 

INSTALLATION

 

 

Pre-Installation Cleaning ............................................ 3 

 

Location and Piping .................................................... 3 

 

Pump Mounting .......................................................... 3 

 

Coupling Alignment .................................................... 4 

 

Pump Rotation ........................................................... 4 

 

To Change Pump Rotation ......................................... 4 

 

Check Valves ............................................................. 4 

 

Manual Bypass Valves ............................................... 4 

OPERATION

 

 

Pre-Start Up Check List .............................................. 5 

 

Start Up Procedures ................................................... 5 

 

Running the Pump in Reverse Rotation ..................... 5 

 

Flushing the Pump ..................................................... 6 

 

Pump Relief Valve ...................................................... 6 

 

Relief Valve Setting and Adjustment .......................... 6 

MAINTENANCE

 

 

Torque Table .............................................................. 7 

 

Scheduled Maintenance ............................................. 7 

 

      Strainers ............................................................... 7 

 

      Lubrication ............................................................ 7 

 

Vane Replacement ..................................................... 8 

 

Pump Disassembly (HXL6 and HXLJ8) ...................... 9 

 

Pump Assembly  (HXL6 and HXLJ8) ......................... 9 

 

Pump Disassembly (HXL8 and HXL10) ................... 11 

 

Pump Assembly  (HXL8 and HXL10) ....................... 12 

TROUBLE SHOOTING

....................................................... 14 

 

Numbers  in  parentheses  following  individual  parts  indicate 
reference numbers on the Blackmer Parts List for the pump 
being serviced. 

PUMP PARTS LISTS 

HXL6 

HXL8, HXLJ8 

HXL10 

102-A01

 

102-A02

 

102-A04

 

Blackmer  pump  manuals  and  parts  lists  may  be  obtained 
from  Blackmer's  website  (www.blackmer.com)  or  by 
contacting Blackmer Customer Service.

 

SAFETY DATA 

 

 

This is a SAFETY ALERT SYMBOL. 

When you see this symbol on the product, or in the 

manual, look for one of the following signal words and be 

alert to the potential for personal injury, death or major 

property damage 

 

Warns of hazards that WILL cause serious personal 

injury, death or major property damage. 

 

Warns of hazards that CAN cause serious personal 

injury, death or major property damage. 

 

Warns of hazards that CAN cause personal injury 

or property damage. 

NOTICE: 

Indicates special instructions which are very 

important and must be followed.

 

 

NOTICE: 

 

Blackmer  Power  Pumps

  MUST

  only  be  installed  in 

systems,  which  have  been  designed  by  qualified 
engineering personnel.  The system 

MUST

 conform to all 

applicable  local  and  national  regulations  and  safety 
standards. 
 
This  manual  is  intended  to  assist  in  the  installation  and 
operation of Blackmer Power pumps, and 

MUST

 be kept 

with the pump. 
 
Pump service shall be performed by qualified technicians 

ONLY

.  Service shall conform to all applicable local and 

national regulations and safety standards. 
 
Thoroughly  review  this  manual,  all  instructions  and 
hazard  warnings, 

BEFORE

  performing  any  work  on  the 

pump. 
 
Maintain 

ALL

  system  and  pump  operation  and  hazard 

warning decals.

 

 
 

Summary of Contents for HXL10E

















Reviews: