BLACKMER XLW2E-N Installation, Operation And Maintenance Instructions Download

Page: 1 / 16

BLACKMER POWER PUMPS

963907

INSTRUCTIONS NO. 105-B00

INSTALLATION OPERATION AND MAINTENANCE INSTRUCTIONS

MODELS: XLW2F, XLW3F, XLW4A

DISCONTINUED MODELS: XLW2E-N, XLW3E-N

Section

Effective

Replaces

105
Jul 2018
Jul 2015

TABLE OF CONTENTS

Page

PUMP DATA

Technical

Data

Initial Pump Start Up Information

INSTALLATION

Pre-Installation

Cleaning

Location and Piping

Mounting - Stationary

Mounting - Truck

Coupling

Alignment

Pump

Rotation

To Change Pump Rotation

Check

Valves

OPERATION

Pre-Start Up Check List

Start Up Procedures

Running the Pump in Reverse Rotation

Flushing the Pump

Pump Relief Valve

Relief Valve Setting and Adjustment

MAINTENANCE

Lubrication 7
Strainers 8
Vane Replacement

Pump Disassembly

Parts Replacement

Pump Assembly

FLANGE MOUNTED GEAR REDUCER MAIN.

TROUBLE SHOOTING

NOTE

Numbers in parentheses following individual parts indicate
reference numbers on Blackmer Parts List No. 105-B01,
105-B02 and 105-B04.

Blackmer pump manuals and parts lists may be obtained
from Blackmer's website (www.blackmer.com) or by
contacting Blackmer Customer Service.

SAFETY DATA

This is a SAFETY ALERT SYMBOL.

When you see this symbol on the product, or in the

manual, look for one of the following signal words and be

alert to the potential for personal injury, death or major

property damage

Warns of hazards that WILL cause serious personal injury,

death or major property damage.

Warns of hazards that CAN cause serious personal injury,

death or major property damage.

Warns of hazards that CAN cause personal injury

or property damage.

NOTICE:

Indicates special instructions which are very

important and must be followed.

NOTICE:

Blackmer Pumps

MUST

only be installed in systems, which

have been designed by qualified engineering personnel.
The system

MUST

conform to all applicable local and

national regulations and safety standards.

This manual is intended to assist in the installation and
operation of the Blackmer XLW Series pumps, and

MUST

be kept with the pump.

Pump service shall be performed by qualified technicians

ONLY

. Service shall conform to all applicable local and

national regulations and safety standards.

Thoroughly review this manual, all instructions and hazard
warnings,

BEFORE

performing any work on the pump.

Maintain

ALL

system and pump operation and hazard

warning decals.

Summary of Contents for XLW2E-N

















Search results

Summary of Contents for XLW2E-N

Reviews:

Related manuals for XLW2E-N

Brands by name

Popular brands

BLACKMER XLW2E-N, Installation, Operation And Maintenance Instructions

Search results

Summary of Contents for XLW2E-N

Reviews:

Related manuals for XLW2E-N

Brands by name

Popular brands