BLACKMER XLW2E-N Installation, Operation And Maintenance Instructions Download

Page: 11 / 16

107-B00 Page 11/16

23. RELIEF VALVE ASSEMBLY

a. Insert the valve (9) into the relief valve bore of the

casing with the fluted end inward.

b. Install the relief valve spring (8) and spring guide (7)

against the valve.

c. Attach a new relief valve O-ring (10) and the valve

cover (4) on the cylinder.

d. Screw the relief valve adjusting screw (2) with locknut

(3) into the valve cover (4) until it makes contact with
the spring guide (7).

e. After the relief valve has been adjusted, tighten the

Locknut (3) and install the relief valve cap (1) and O-
ring (88)

NOTICE:

The relief valve setting MUST be tested and adjusted
more precisely before putting the pump into service.
Refer to "Relief Valve Setting and Adjustment"

Operation without guards in place can
cause serious personal injury, major
property damage, or death.

Do not operate

without guard in

place.

24. Reinstall coupling, shaft key, and coupling guards.

25. Refer to “Pre-Start Up Check List” and “Start Up

Procedures” sections of this manual prior to restarting
pump operation.

Summary of Contents for XLW2E-N

















Search results

Summary of Contents for XLW2E-N

Reviews:

Related manuals for XLW2E-N

Brands by name

Popular brands

BLACKMER XLW2E-N, Installation, Operation And Maintenance Instructions

Search results

Summary of Contents for XLW2E-N

Reviews:

Related manuals for XLW2E-N

Brands by name

Popular brands