background image

5

4

English

English

Warning!

Important safety information!

READ THE FOLLOWING INFORMATION CAREFULLY. SAVE ALL 
INSTRUCTIONS FOR FUTURE REFERENCE!

Follow all warnings and instructions marked on the product!

Danger!  High internal operating voltages.

Do not open the equipment case. There are no user serviceable parts in this 
equipment.  Refer all servicing to qualified service personnel. 

Clean only with dry cloth.

Condensation  can  form  on  the  inside  of  an  amplifier  if  it  is  moved  from  a  cold 
environment to a warmer location. Before switching the unit on, it is recommended 
that the unit be allowed to reach room temperature. 

Unauthorised  modification  of  this  equipment  is  expressly  forbidden  by  Blackstar 
Amplification Ltd.

Never push objects of any kind into ventilation slots on the equipment casing.

Do not expose this apparatus to rain, liquids or moisture of any type. 

Do not place this product on an unstable trolley, stand or table. The product may 
fall, causing serious damage to the product or to persons!

Do not cover or block ventilation slots or openings. 

This product should not be placed near a source of heat such as a stove, radiator, 
or another heat producing amplifier.

Use only the supplied power cord which is compatible with the mains voltage 
supply in your area.

Power supply cords should always be handled carefully and should be replaced if 
damaged in any way.

Never break off the earth (ground) pin on the power supply cord.

The power supply cord should be unplugged when the unit is to be unused for long 
periods of time.

Before the unit is switched on, the loudspeaker should be connected as described 
in the handbook using the lead recommended by the manufacturer.

Always replace damaged fuses with the correct rating and type.

Never disconnect the protective mains earth connection.

High loudspeaker levels can cause permanent hearing damage. You should 
therefore avoid the direct vicinity of loudspeakers operating at high levels. Wear 
hearing protection if continuously exposed to high levels.

If the product does not operate normally when the operating instructions are 
followed, then refer the product to a qualified service engineer.

The U.S. Government´s Occupational Safety and Health Administration (OSHA) has 
specified the following permissible noise level exposures:

Duration Per Day In Hours 

Sound Level dBA, Slow Response

8  

90

6  

92

4  

95

3  

97

2  

100

1½  

102

1 105
½ 110
¼ or less  

115

According to OSHA, any exposure in excess of the above permissible limits could 
result in some hearing loss.

Ear plug protectors in the ear canals or over the ears must be worn when operating 
this amplification system in order to prevent a permanent hearing loss if exposure 
is in excess of the limits as set forth above. To ensure against potentially dangerous 
exposure to high sound pressure levels, it is recommended that all persons 
exposed to equipment capable of producing high sound pressure levels such as 
this  amplification  system  be  protected  by  hearing  protectors  while  this  unit  is  in 
operation.

All electrical and electronic products should be disposed of separately 

from the municipal waste stream via designated collection facilities 

appointed by the government or the local authorities.

Summary of Contents for HT METAL 100





























Reviews: