background image

11

10

19. ISF (Infinite Shape Feature) 

The  patented  ISF  control  works  in  conjunction  with  the  Bass, 
Middle and Treble controls. It allows you to choose the exact 
tonal signature you prefer. Fully counter clockwise has a more 
American characteristic with a tight bottom-end and more 
aggressive middle, and fully clockwise has a British characteristic 
which is more ‘woody’ and less aggressive. 

Unlike conventional ‘contour’ controls and parametric equalisation systems, the 
Bass, Middle and Treble controls remain interactive with each other just like in a 
traditional guitar amplifier tone stack. This leads to a very familiar, musical response.

Master
20. Reverb

The Reverb control sets the overall level of the reverb effect. With the control fully 
counter clockwise there will be no reverb. Turning the control clockwise will increase 
the amount of reverb.

21. Resonance 

The  Resonance  control  sets  the  overall  bass  response  of  the  amplifier.  At  lower 
settings the cleans will be tight and funky and overdrives will be focussed in their 
bass response. At increased settings the clean sounds will become full and warm, 
whilst the crunch and overdrive tones will be more bass heavy and resonant.

22. Presence 

The Presence control sets the overall treble response of the amplifier. Percussive 
high-end can be accentuated on clean sounds and the amount of aggressive treble 
controlled with crunch and overdrive settings. 

23. Volume 

This controls the overall volume of your amplifier. Turning it clockwise increases the 
volume.

24. Power Indicator Light

The power indicator will light when the amplifier is switched on.

25. Standby

This switch enables the output stage. Always turn this switch on at least 30 seconds 
after the Power switch (26). During short breaks in playing use just this switch to 
turn ‘off’ and ‘on’ the amplifier’s output.

26. Power

This  switch  is  used  to  turn  the  amplifier  on  and  off.  You  should  always  turn  this 
switch on before turning on the Standby switch (25).

Rear Panel

1. Mains Fuse

The value of the Mains Fuse is specified on the rear panel. Never use a fuse of the 
incorrect value or attempt to bypass it.

2. Mains Input

The supplied detachable mains lead is connected here. The lead should only be 
connected to a power outlet that is compatible with the voltage, power and frequency 
requirements stated on the rear panel. If in doubt get advice from a qualified technician.

3. H.T. Fuse

The value of the H.T. Fuse is specified on the rear panel. Never use a fuse of the 
incorrect value or attempt to bypass it.

4. Speaker Outputs

The output marked ‘1x16 Ohm’ is for the connection of a single 16 Ohm extension 
speaker cabinet.

The outputs marked ‘1x8 Ohm or 2x16 Ohm’ are for the connection of either a 
single 8 Ohm extension cabinet or two 16 Ohm cabinets.

The outputs marked ‘1x4 Ohm or 2x8 Ohm’ are for the connection of either a single 
4 Ohm extension cabinet or two 8 Ohm cabinets. Also, the internal loudspeaker 
of the HT METAL 60 can be plugged in here if it is used with an 8 Ohm extension 
cabinet.See table below.
 

‘1x16 Ohm’ 

‘1x8 Ohm or 2x16  ‘1x4 Ohm or 2x8 

 

 output 

 Ohm’ outputs 

Ohm’ outputs

Internal 2x16 Ohm combo speakers 

 

X X

One 16 Ohm extension cabinet 

 

X X

Two 16 Ohm extension cabinets 

 

 

X X

Internal 2x16 Ohm combo speakers 

  

 

plus one 8 Ohm extension cab

One 8 Ohm extension cabinet 

 

X X

Two 8 Ohm extension cabinets 

 

Single 4 Ohm extension cabinet 

 X

WARNING:

 The output marked ‘1x16 Ohm’ should never be used at the same 

time as any of the outputs marked ‘1x8 Ohm or 2x16 Ohm’ or ‘1x4 Ohm or 2x8 
Ohm’ outputs. The outputs marked ‘1x8 Ohm or 2x16 Ohm’ or ‘1x4 Ohm or 2x8 
Ohm’ outputs should never be used at the same time. Failure to correctly match the 
impedance of the amplifier and speakers will damage the amplifier.

5. Speaker Emulated Output 

This output emulates the tonal characteristics of a guitar speaker cabinet and 
provides a natural valve overdrive tone for connection to a recording device or 
mixing desk. Always use a good quality screened lead. 

English

English

USA

UK

Summary of Contents for HT METAL 100





























Reviews: