background image

4

EN

Box Contents

Charging Warnings

WARNING:

 Failure to exercise caution while using this product and comply 

with the following warnings could result in product malfunction, electrical 

issues, excessive heat, FIRE, and ultimately injury and property damage.

• NEVER LEAVE THE POWER SUPPLY, CHARGER AND BATTERY UNATTENDED 

DURING USE.

• NEVER CHARGE BATTERIES OVERNIGHT.

• Never attempt to charge dead, damaged or wet battery packs.
• Never attempt to charge a battery pack containing different types of batteries.
• Never allow children under 14 years of age to charge battery packs.
• Never charge batteries in extremely hot or cold places or place in direct 

sunlight.

• Never charge a battery if the cable has been pinched or shorted.
• Never connect the charger if the power cable has been pinched or shorted.
• Never attempt to dismantle the charger or use a damaged charger.
• Never drop charger or batteries.
• Always use only rechargeable Li-Po batteries designed for use with this type 

of charger.

• Always inspect the battery before charging.
• Always keep the battery away from any material that could be affected by 

heat.

• Always monitor the charging area and have a fi re extinguisher available at all 

times.

• Always end the charging process if the battery becomes hot to the touch or 

starts to change form (swell) during the charge process.

• Always connect the charge cable to the charger fi rst, then connect the battery 

to avoid short circuit between the charge leads. Reverse the sequence when 
disconnecting.

• Always connect the positive red leads (+) and negative black leads (–) cor-

rectly.

• Always disconnect the battery after charging, and let the charger cool between 

charges.

• Always charge in a well-ventilated area.
• Always terminate all processes and contact Horizon Hobby if the product 

malfunctions.

Low Voltage Cutoff  (LVC)

Low voltage cutoff (LVC) protects the Li-Po battery from over-discharge in fl ight 
and activates when the battery reaches a preset value. When the battery is 
discharged to the cutoff point, the aircraft will display rapidly fl ashing red, green 
and blue LEDs to warn you it’s time to land. When you see this LED code, land 
immediately to prevent over-discharge and damage to the battery.

When the LVC is activated, you have approximately 2 minutes until the battery is 
depleted and can no longer maintain a hover. Repeated fl ying to LVC will damage 
the battery.

NOTICE:

 Crash damage and battery damage are not covered under warranty. 

IMPORTANT: 

Always disconnect and remove the Li-Po battery from the aircraft 

after each fl ight. Charge your Li-Po battery to about half capacity before storage. 
During storage, make sure the battery charge does not fall below 3V per cell. 
A connected battery will result in trickle discharge.

• Blade 350 QX3
• CGO2 3-Axis Camera/Gimbal (AP Combo)
• 3000mAh 3S 11.1V 20C Li-Po Battery
• 3S DC Li-Po Balancing Charger with 5A AC Power Supply
• Spektrum DX4 DSMX

4-Channel Transmitter (RTF, AP Combo)

• 4 AA Batteries (RTF, AP Combo)
• Cell Phone Mount

Summary of Contents for 350 QX3

















Reviews: