background image

8

EN

Elevator

Forward

Elevator down

Elevator up

Backward

Left Side View

Left Side View

Aileron

Aileron left

Left

Aileron right

Right

Rear View

Rear View

NOTICE:

 Never power on the video transmitter without the antenna 

installed. Powering on without the antenna will damage the video 
transmitter. 

The video transmitter is located under the top plate of the quadcopter, 
with access holes to allow changing the band and channel, as shown in 
the illustration. 
At power up the digital display will fl ash 2 numbers repeatedly, indicat-
ing it is locked. The number with the “dot” is the selected BAND (1.-5.), 
the second number is the channel (1-8).

Channel Selection:

1. To unlock the display push and hold the

Channel Select button for 2 seconds.

2. Press the button to cycle through the channels (1-8).
3. Press and hold the button for 2 seconds to exit Channel Select.

If you are changing bands, proceed to 

Step 3

 of the Band Selection section.

4.  Press and hold the button again for 2 seconds to exit and lock the display.

Band Selection:

1. Press and hold the button for 2 seconds to enter Channel Select.
2. Press and hold the button again for 2 seconds to swich from

Channel Select to Band select.

3. Press the button to cycle through the Bands (1-5).
4. Press and hold the button for 2 seconds to exit and lock the display.

Using the Video Transmitter

Channel Select Button

Digital Display

Dot Indicating 

Band Selected

Display Locked

Channel Selection

Select desired channel

Select desired band

Band Selection

Hold for 2 seconds

Programming Flowchart

Hold for 2 seconds

Hold for 2 seconds

CH 1

CH 2 

CH 3

CH 4

CH 5

CH 6

CH 7

CH 8

1. Band A

5865

5845

5825

5805

5785

5765

5745

5725

2. Band B

5733

5725

5771

5790

5809

5828

5847

5866

3. Band E**

5705

5685

5665

N/A

5885

5905

N/A

N/A

4. FS/IRC

5740

5760

5780

5800

5820

5840

5860

5880

5. RaceBand

5658

5695

5732

5769

5806

5843

5880

5917

** E band Channels 4, 7 and 8 have been removed to prevent transmitting outside of designated Amature radio frequencies

Band Number

Channel Number

Available Frequencies (mHz)

Summary of Contents for BLH02000
















Reviews: