background image

www.blaubergventilatoren.de

vento expert (Duo) a50(30)-1 Pro/Pro3

5

THE UNIT SHOULD NOT BE OPERATED BY CHILDREN OR PERSONS WITH REDUCED 

PHYSICAL, MENTAL, OR SENSORY CAPACITIES, OR THOSE WITHOUT THE APPROPRIATE 

TRAINING.

THE UNIT MUST BE INSTALLED AND CONNECTED ONLY BY PROPERLY QUALIFIED 

PERSONNEL AFTER THE APPROPRIATE BRIEFING.

THE CHOICE OF UNIT INSTALLATION LOCATION MUST PREVENT UNAUTHORIZED 

ACCESS BY UNATTENDED CHILDREN.

PURPOSE

The ventilator is designed to ensure continuous mechanical air exchange in flats, cottages, hotels, cafés and other domestic and public 
premises. The ventilator is equipped with a regenerator that enables supply of fresh filtered air heated by means of extract air heat energy 
recovery. The ventilator is designed for wall flush mounting.

The unit is rated for continuous operation without disconnection from the power supply.
Transported air must not contain any flammable or explosive mixtures, evaporation of chemicals, sticky substances, fibrous materials, 
coarse dust, soot and oil particles or environments favourable for the formation of hazardous substances (toxic substances, dust, 
pathogenic germs).

Name

Vento Expert A50-1 Pro/Pro3

Vento Expert Duo A30-1 Pro

Indoor unit of the ventilator

1 pc.

1 pc.

Air duct

1 pc.

1 pc.

Air flow distributor

3-6 pcs.

Sound-absorbing material

1 pc.

Assembled cartridge

1 pc.

1 pc.

Outer ventilation hood

1 pc.

1 pc.

Remote control

1 pc.

1 pc.

Cardboard template

1 pc.

1 pc.

Fastening set

2 packs

2 packs

Foam wedges

1 set

1 set

User's manual

1 pc.

1 pc.

Mounting hood installation instruction

1 pc.

1 pc.

Packing box

1 pc.

1 pc.

Vento

Expert A 50 -1 L S10 Pro

Automation availability

Pro – controls and control unit are included in the delivery set
Pro3 – model without automatic shutters, with manual airflow blocking

Ventilation hood model
Air duct length

_ – 500 mm
L – 700 mm
L035 – 350 mm
L10 – 1000 mm

Front panel modification

1 – flat front panel

Rated air flow [m3/h]
Air duct cross section

A – round

Ventilator series

Expert is a series of reversible ventilators with a unidirectional air flow.
Expert Duo is a series of reversible ventilators with a countercurrent air flow.

DELIVERY SET

DESIGNATION KEY

Summary of Contents for 4058448022999

























Reviews: