background image

www.blaubergventilatoren.de

3

KOMFORT EC SKE270-1.5

BLAUBERG Ventilatoren GmbH Company is happy to offer your attention 

a new heat recovery air handling unit 

KOMFORT EC SKE270-1.5

 with 

integrated kitchen hood.

INTRODUCTION

The present operation manual contains a technical description, technical 

data sheets, operation and mounting guidelines, safety precautions and 

warnings for safe and correct operation of the unit.  

Read carefully and understand the operation manual, especially the safety 

requirements, before the unit mounting and start up.

Keep the operation manual available as long as you use the unit.

GENERAL

The heat recovery air handling unit KOMFORT EC SKE270-1.5 with integrated 

kitchen hood is designed for efficient and energy saving ventilation of 

domestic premises. 

The unit is not a ready to use product but a component part of central air 

conditioning and ventilation network. 

The unit is designed for wall mounting. 

The unit is available for round Ø125 mm air ducts.

The unit is rated for indoor application at ambient temperature from +1 °C 

up to +60 °C and relative humidity not exceeding 80%. The transported air 

temperature is allowed from -25 °C up to +60 °C.

Hazardous parts access and water ingress protection rating:

  Unit motors - IP 44;

  Assembled unit connected to air ducts - IP 22.

The unit design is regularly improved, so some models can slightly differ 

from those ones described in this service instruction.

SAFETY RULES

All operations related to the unit electrical connections, servicing and 

repair works are allowed only after the unit disconnection from power mains.  

The unit is rated as a Class I electrical appliance.

All mounting and servicing operations are allowed by duly qualified 

personnel. 

Please follow the safety regulations and working instructions (DIN EN 50 

110, IEC 364).

Make sure the impeller and the casing are not damaged before connecting 

the unit to power mains. The casing internals must be free of any foreign 

objects which can damage the impeller blades.

The unit maintenance and repair is allowed only after power cut-off and full 

stop of the rotating parts.

Misuse of the unit or any unauthorized modification are not allowed. 

The unit is designed for connection to ac single-phase power mains, see 

«Technical Data». 

The unit is rated for permanent operation.

Take steps to prevent ingress of smoke, carbon monoxide and other 

combustion products into the room through open chimney flues or other 

fire-protection devices. Sufficient air supply must be provided for proper 

combustion and exhaust of gases through the chimney of fuel burning 

equipment to prevent back drafting.  The maximum permitted pressure 

difference per living units is 4 Pa.

The transported air must not contain any dust or other solid impurities, 

sticky substances or fibrous materials.

The unit is not rated for operation in a flammable or explosive medium. 

Fulfil the operation manual requirements to ensure a trouble-free and long 

service life of the unit. 

TRANSPORTATION AND STORAGE RULES

Transportation of the unit is allowed by any vehicle provided the unit is 

transported in the original package and is protected against weather and 

mechanical damages. 

Use hoist machinery for handling and transportation to prevent possible 

mechanical damages of the unit. Fulfil the requirements for transportation of 

the specified cargo type during cargo-handling operations. 

Store the unit in a dry and cool place in the original packing.

The storage environment must not be subjected to any aggressive and/

or chemical evaporations, admixtures, foreign objects that may provoke 

corrosion and damage connection tightness. 

Store the unit in an environment with minimized risk of mechanical 

damages, temperature and humidity fluctuations. 

Do not expose the unit to the temperatures below  +5 °C and above  +40 

°C .

Connection of the unit to power mains is allowed after the unit has been 

kept indoor for minimum two hours.

MANUFACTURER’S WARRANTY

The unit complies with the requirements according to the EU norms 

and directives, to the relevant EU-Low Voltage Equipment Directives, EU-

Directives on Electromagnetic Compatibility. 

We hereby declare that the unit complies with the essential protection 

requirements of Electromagnetic Council Directive 2004/108/EC, 89/336/EEC 

and Low Voltage Directive 2006/95/EC, 73/23/EEC and CE-marking Directive 

93/68/EEC on the approximation of the laws of the Member States relating to 

electromagnetic compatibility. This certificate is issued following test carried 

out on samples of the product referred to above. Assessment of compliance of 

the product with the requirements relating to electromagnetic compatibility 

was based on the following standards.

The manufacturer hereby warrants normal operation of the unit over the 

period of two years from the retail sale date provided observance of the 

installation and operation regulations.

In case of failure due to manufacturing fault during the warranty period the 

consumer has the right to exchange it.

The replacement is offered by the Seller. 

If case of no confirmation of the sale date, the warranty period shall be 

calculated from the manufacturing date.

The manufacturer shall not be liable for any damage resulting from any 

misuse of or gross mechanical interference with the unit.

The manufacturer is not responsible for the damages resulted due to the 

use of  third party equipment or to third party equipment.

                   

WARNING

 

Do not dispose in domestic waste. 

The unit contains in part material that 

can be recycled and in part substances 

that should not end up as domestic waste. Dispose 

of the unit once it has reached the end of its work-

ing life according to the regulations valid in your 

country.

 

                  

WARNING

The unit is not allowed for use by chil-

dren and persons with reduced physi-

cal, mental or sensory capacities, without proper 

practical experience or expertise, unless they are 

controlled or instructed on the product operation 

by the person(s) responsible for their safety. Super-

vise the children and do not let them play with the 

product. 

!

KOMFORT_EC_SKE270_v2(4)_EN.indd   3

07.08.2015   14:25:41

Summary of Contents for KOMFORT EC SKE270-1.5





















Reviews: