background image

KoMFort Erv d

14

www.blaubergventilatoren.de

Unit Type

Energy recovery air handling unit

Seller’s Stamp

Model

KOMFORT ERV D___________

Serial Number
Manufacture Date
Purchase Date
Warranty Period

Seller

Unit Type

Energy recovery air handling unit

Model

KOMFORT ERV D___________

Serial Number
Manufacture Date

Quality Inspector’s

Stamp

Seller

Seller’s Stamp

Address
Phone Number
E-mail
Purchase Date

This is to certify acceptance of the complete unit delivery with the user’s manual. The warranty terms are 
acknowledged and accepted.

Customer’s Signature

The KOMFORT ERV D___________ unit is installed pursuant to the requirements stated in the present 
user's manual.

Installation Stamp

Company name
Address
Phone Number
Installation

Technician’s Full Name
Installation Date:

Signature:

The unit has been installed in accordance with the provisions of all the applicable local and national construction, 
electrical and technical codes and standards. The unit operates normally as intended by the manufacturer.

Signature:

SELLER INFORMATION

CERTIFICATE OF ACCEPTANCE

INSTALLATION CERTIFICATE

WARRANTY CARD

Summary of Contents for KOMFORT ERV D150

















Reviews: