BLAUBERG Ventilatoren KOMFORT LE Series Operation Manual Download | Manualshive

Page: 19 / 20

background image

www.blaubergventilatoren.de

19

KOMFORT LE

The air handling unit with heat recovery

KOMFORT LE350-3
KOMFORT LE500-3
KOMFORT LE530-4
KOMFORT LE600-4

KOMFORT LE800-9
KOMFORT LE1200-9
KOMFORT LE1700-18
KOMFORT LE2200-18

is recognizes as serviceable.

The unit complies with the requirements according to the EU norms and directives, to the relevant EU-Low Voltage Equipment Directives, EU-Directives

on Electromagnetic Compatibility.

We hereby declare that the following product complies with the essential protection requirements of Electromagnetic Council Directive 2004/108/EC, 89/336/

EEC and Low Voltage Directive 2006/95/EC, 73/23/EEC and CE-marking Directive 93/68/EEC on the approximation of the laws of the Member States relating to

electromagnetic compatibility.

This certificate is issued following test carried out on samples of the product referred to above.

Approval mark

Manufacturing date ____________________

Company:

Name:

Date Signature

The air handling unit with heat recovery

KOMFORT LE350-3
KOMFORT LE500-3
KOMFORT LE530-4
KOMFORT LE600-4

KOMFORT LE800-9
KOMFORT LE1200-9
KOMFORT LE1700-18
KOMFORT LE2200-18

is connected to power mains in compliance with the operation manual requirements by the professional:

SELLER

SALES DATE

REPRESENTATIVE IN EU
BLAUBERG Ventilatoren GmbH

Aidenbachstr. 52a

D-81379 Munich,

Germany

ACCEPTANCE CERTIFICATE

CONNECTION CERTIFICATE

WARANTY CARD

KOMFORT LE350-3
KOMFORT LE500-3
KOMFORT LE530-4
KOMFORT LE600-4

KOMFORT LE800-9
KOMFORT LE1200-9
KOMFORT LE1700-18
KOMFORT LE2200-18

KOMFORT_LE_v2(2)_EN.indd 19

10.08.2015 12:00:53

«
...
17
18
19
20
»

Summary of Contents for KOMFORT LE Series





















Reviews:

No comments

Related manuals for KOMFORT LE Series

Brand: Komfovent Pages: 52

Brand: Vents Pages: 16

KOMFORT EC S200

Brand: BLAUBERG Ventilatoren Pages: 24

KOMFORT Ultra D 105-A

Brand: BLAUBERG Ventilatoren Pages: 16

AERO MASTER XP 04

Brand: Remak Pages: 50

Brand: Samsung Pages: 2

Brand: Vent-Axia Pages: 16

Brand: Kampmann Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands