background image

THE UNIT CAN BE USED IN KITCHEN SPACES ONLY IF THERE IS A GREASE FILTER.

INSTALL A KITCHEN HOOD WITH A GREASE FILTER IF AIR IS EXTRACTED FROM THE 

COOKING SURFACE.

www.blaubergventilatoren.de

KoMFort roto ec S2(e)200

4

DELIVERY SET

DESIGNATION KEY

PURPOSE

The unit is designed to ensure continuous mechanical air exchange in houses, offices, hotels, cafes, conference halls, and other utility 
and public spaces as well as to recover the heat energy contained in the air extracted from the premises to warm up the filtered stream 
of intake air.
The unit is not intended for organizing ventilation in swimming pools, saunas, greenhouses, summer gardens, and other spaces with 
high humidity.
Due to the ability to save heating energy by means of energy recovery, the unit is an important element of energy-efficient premises. 
The unit is a component part and is not designed for stand-alone operation. 
It is rated for continuous operation.
Transported air must not contain any flammable or explosive mixtures, evaporation of chemicals, sticky substances, fibrous materials, 
coarse dust, soot and oil particles or environments favourable for the formation of hazardous substances (toxic substances, dust, 
pathogenic germs). 

THE UNIT SHOULD NOT BE OPERATED BY CHILDREN OR PERSONS WITH REDUCED 

PHYSICAL, MENTAL, OR SENSORY CAPACITIES, OR THOSE WITHOUT 

THE APPROPRIATE TRAINING. 

THE UNIT MUST BE INSTALLED AND CONNECTED ONLY BY PROPERLY QUALIFIED 

PERSONNEL AFTER THE APPROPRIATE BRIEFING.

THE CHOICE OF UNIT INSTALLATION LOCATION MUST PREVENT UNAUTHORIZED 

ACCESS BY UNATTENDED CHILDREN.

KOMFORT Roto

EC S 2 E 200

Rated air flow [m

3

/h]

Electric heater

_ — without an electric heater
E — with an electric heater

Panel thickness

2 — 20 mm

Spigot orientation

S — vertical

Motor type

EC — electronically commutated

Series of units

Roto — heat recovery air handling unit with a rotary heat exchanger

Name

Number

Air handling unit 

1  pc.

User’s manual

1  pc.

Control panel*

1  pc.

Decorative panel

1  pc.

Decorative panel mounting bracket

4  pcs.

Installation kit 

1  pc.

Packing box 

1  pc.

*Control panel is not included in delivery set of units equipped with S21 controller.

Summary of Contents for KOMFORT Roto EC S2 200





















Reviews: