background image

TECHNICAL MAINTENANCE

Maintenance operations of the unit are required 3-4 times per year. They include general cleaning of the unit and the following operations:

1. Filter maintenance (3-4 times per year). 

Dirty filters increase air resistance in the system and reduce supply air volume. The filters require cleaning not less than 3-4 times per year. 
Vacuum cleaning is allowed. After two consecutive cleanings filters must be replaced. For new filters contact the Seller.  

Replacement of filters in KOMFORT Ultra D 105-A units:

Unscrew the manual screws on the 
removable filter service plates.  

Remove the 

service

 plates.

Remove the filters by pulling them down.
Install new or cleaned filters in their 
original place.

1

2

3

1

2

3

1

2

3

Replacement of filters in KOMFORT Ultra D 105 units:

Press out on the latches. 

Remove the service panel. 

Remove the filters by pulling them down.
Install new or cleaned filters in their 
original place. 

3

1

2

3

1

2

3

1

2

DISCONNECT THE UNIT FROM POWER SUPPLY BEFORE ANY MAINTENANCE 

OPERATIONS!

MAKE SURE THE UNIT IS DISCONNECTED FROM POWER MAINS BEFORE REMOVING THE 

PROTECTION!

www.blaubergventilatoren.de

KOMFOrt ultra d 105(-A)

10

Summary of Contents for KOMFORT Ultra D 105

















Reviews: