Blaupunkt VELOCITY 2GO 5, Operating And Installation Manual

9

Velocity 2Go 5 / 2Go 6 

The warranty terms can be called up under 

www.blaupunkt.usa.com 

or requested directly from: 

Blaupunkt USA
2800 South 25th Av.
Broadview, IL 60155
PH: 800-950-2528

FX: 708-865-5296

EM: blau.tech.support@us.bosch.com

Safety notes

Please observe the following safety notes 
during the installation and connection.

-   Disconnect the negative pole of the battery! Ob-

serve the safety notes of the vehicle manufacturer.

-   When you drill holes, ensure that you do not dam-

age any vehicle components.

-  If the positive and negative cable are extended, en-

sure that the cross section is not less than

1.5

mm

2

.

-  An incorrect installation can result in malfunctions 

of the electronic vehicle systems or your car sound 
system.

Installation and connection instructions

With respect to accident safety, the Velocity 2Go 5 / 
2Go 6 must be installed professionally.
A dry location should be selected for the installation 
location.

The Velocity 2Go 5 / 2Go 6 must not be installed on 
rear shelves, rear seats or other locations that are open 
to the front.

The installation surface must be suitable to accept 
the enclosed retaining straps or the QuickOut bracket 
available as an option (7 606 500 190) and provide 
secure support. 

To protect the equipment, the +12-V connecting cable 

must

 be fi tted with a fuse no more than 30 cm from 

the battery.

Switching on/off

A specialty of the Velocity 2Go 5 / 2Go 6 is its 

automatic 

switch-on system

. 

"Auto"  If a music signal is received at one of the 

3 inputs, the subwoofer box switches on au-
tomatically if the power switch at the top of 
the device is set to "Auto" (automatic), see page 
4 / Fig. 2.

If the music signal stays out for more than 
60 seconds, the Velocity 2Go 5 / 2Go 6 auto-
matically switches off.

"ON" 

Velocity 2Go 5 / 2Go 6 is always switched on. 

"OFF" 

Velocity 2Go 5 / 2Go 6 is switched off.

Note:

If connected via the multiport, the "Auto" switch-on 
system is always activated.

Connection 

(see page 3 / Fig. 1)

The connection is connected with battery plus and 
vehicle ground. 

The control of the Velocity 2Go 5 / 2Go 6 should ideally 
utilise 2 channels, optionally via the preamplifi er outputs 
or the loudspeaker outputs of the car sound system. 
A control solely via the right or left channel is also pos-
sible since the low-frequency portion of the music is 
generally identical on both channels. 

The preamplifi er outputs are connected to the cinch 
(RCA) sockets directly at the device or alternatively to 
the multiport connecting cable using a shielded cable. 

To connect the device, we explicitly recommend 
the use of the original Blaupunkt cinch cable 
7 607 885 093 (1.3 m) or 7 607 886 093 (5 m). 

With control via the loudspeaker outputs of the radio, 
the input connections of the multiport connecting cable 
are fed to the closest loudspeaker cables (front or rear) 
on the left and right. They are separated and connected 
to the input connections. 

The polarity of the + or - connections must be ob-
served. 

Bridge output stages (BTL) can also be connected 
directly without an additional adapter.

TIM function

For car sound systems with activated TIM function, 
the Velocity 2Go 5 / 2Go 6 should not be controlled via 
the cinch inputs, but via the loudspeaker outputs of the 
car sound system.

Connection to MP3 player

The connection is implemented by connecting the en-
closed 30 cm connecting cable with 3.5-mm jack plugs 
to the MP3-IN signal source (at the top of the device), 
see page 4 / Fig. 3.

Please use only the enclosed connecting cable or a 
comparable cable with angled connector.

Audio mode switch 

(see page 4 / Fig. 4)

The audio mode switch on the top allows switching the 
operating mode "Full" range or "Sub"-woofer. 

In the switch setting "Auto", the operating mode is auto-
matically switched to "Sub" as soon as the Velocity 2Go 5 / 
2Go 6 is connected via the multiport on the rear side. 

"Sub" woofer mode settings

The following control settings are recommended as basic 
setting before the startup: 

Sensitivity (subwoofer gain) to left stop, phase to left 
stop, fi lter (crossover) to center position (see page 5 / 
Fig. 5). 

V_2GO_29.03.07.indd   9

V_2GO_29.03.07.indd   9

02.04.2007   8:44:16 Uhr

02.04.2007   8:44:16 Uhr