background image

GENERAL

  - Making coffee with any of the Blickman filter systems is as simple as it is quick. First, carefully follow the 

operating instructions on pg. 3-4, then pick up the specific directions below which apply to your filter.

 

TRI-SAVER SYSTEM 

LOADING FILTER

 - Be sure your filter is thoroughly clean before using. Spread the coffee grounds evenly 

in the bottom of the filter. (No filter paper is required.) Lock spreader plate in place on filter. 

CARE OF FILTER

  - The Tri-Saver filter is durably constructed and will give you long, uninterrupted 

service with reasonable care. Avoid striking or hitting your Tri-Saver against the receptacle that is used for 
emptying the grounds. Flush out the old coffee grounds with hot water. 

CLEANING FILTER

 - Clean your Tri-Saver thoroughly with hot water after each brewing operation. At the 

end of the day, or at frequent intervals, fill a sink half full of hot water containing approximately one 
teaspoonful of any good free-rinsing detergent per gallon and submerge the filter. Push the filter in an 
upward and downward motion, so that the water will flow through the filter plates, cleaning them 
thoroughly. Daily care will keep your filter clean and will assure perfect coffee flavor. 

IF, FOR ANY REASON, YOUR TRI-SAVER FILTER DOES NOT GIVE YOU VERY 
SATISFACTORY RESULTS, COMMUNICATE WITH US OR YOUR DEALER 
PROMPTLY. YOU WILL RECEIVE PROMPT SERVICE AND FURTHER 
INSTRUCTIONS SHOULD ANY BE REQUIRED.

 

BREW 'N TOSS FILTER PAPER 

FILTER PAPER -

 Be certain you have the correct size paper for your Brew 'n Toss paper holder.

 

LOADING FILTER

  - Swing three wire handles up and out of the wire basket. Set a single sheet of filter paper into 

basket and swing back the three handles to hold the paper firmly in place. Spread coffee evenly over bottom of filter 

paper and set filter in top of urn.

 

CLEANING FILTER -

 Remove basket, dump filter paper and grounds into waste receptacle and rinse wire basket.

 

NOTE: Cloth bag may also be used in brew 'n toss basket. Urn 

furnished standard with bale-type ring with cloth bag.

 

8LSQ

 

FILTER 

SYSTEMS 

 

 

Summary of Contents for LSQ 600 series

















Reviews: