background image

8

BAVM-860 SAW Series 

Instruction Manual

2.2 Product Specification

RF Typical

Frequency Range: ...........................  CATV channels 2 to 79 

Output Level: .......................................................  55 dBmV
Output Level Range: .........   15 dB, continuously adjustable
 

 

 

by front panel Output Level Control

Audio/Video Carrier Ratio Control: ...........   -9 dB to -20 dB,

Frequency Tolerance: ............   ±10 kHz - standard channels

 

 

 

±5 kHz FCC 21006 Offsets

Audio Carrier Frequency Setting: ....................  ±1 kHz, Max

 

 

 

4.5 MHz above video carrier

RF to Video Response  

 

 

from Fv -0.5 MHz to Fv +4.2 MHz: .........   1 dB P/V

Broadband Noise .....................................................  -90 dB
Spurious Output in 50 – 860 MHz Range 

 

@ +55 dBmV Output: .........................................-60 dB

Output Match (Return Loss): ...................................... 12 dB
Vestigial Sideband Reponse:
  @Channel 

Edge ...........................................-20 dB

  @Adjacent 

Channel .....................................-40 dB

Video

Input for 87.5% Modulation: .................   0.7 V to 2.5 V P-P
Video Input Return Loss: ..........................................   18 dB
Video Carrier-To-Noise Ratio in 4 MHz Bandwidth: ..  60 dB
P-P Video to 60 Hz RMS Hum Ratio: .........................   60 dB
Differential Gain at 87.5% Modulation: .....................   ≤ 5%
Differential Phase at 87.5% Modulation: .....................  ≤ 5°
Group Delay ...................................................... 170 ± 50 nS

Audio

Input Impedance: .........................   10K Ohms, Unbalanced
Input for 25 KHz Peak Deviation: ...................  140 mV RMS
Audio Frequency Response: ...................................   ±1.0 dB 

 

(50 Hz to 15 kHz ref to std 75 msec pre-emphasis)

4.5 MHz Intercarrier Stability: ..............................   ±5.0 kHz

General

Power Requirements: ...............  105-130 VAC, 60 Hz, 10 W
Temperature Range: ..............................   0 to 50 degrees C

Mechanical

Dimensions: ..................   19 x 1.75 x 3.5, W x H x D, inches
Mounting:   .........................................19” single rack space
Line Cord: .....  3 wire grounded, 3 wire convenience outlet
Finish:   .................................................................... Plated
Shipping Weight: .........................................   4 lbs. (approx)

Connectors

Audio In: ...............................................................  “F” Type
Video In:  ...............................................................  “F” Type
RF Out:   ...............................................................  “F” Type
RF Output Test - 30 dB: .........................................  “F” Type

Summary of Contents for BAVM-860 SAW Series













Reviews: