background image

11

BT-CMTS Series

Setup Guide

Local Provision Switch

Enable 3.0CM Profiles <ON or OFF>: the TFTP server can contain a DOCSIS 2.0 and DOCSIS 3.0 config file for CMs. Turning 

this OFF will only allow DOCSIS 2.0 configuration files to be sent to CMs.

DHCP Time Configuration

Allows user to set the 

Lease Time

 for IP addresses, in 

DAY

S, 

HOURS

MINUTES

 and 

SECONDS

.

DNS Server Address Configuration

Allows user to set a 

PRIMARY

 and 

SECONDARY DNS (Domain Name Server) address.

1

2

3

6.1 “Local Provision IPv4 Global Config” Tab (continued)

6.2 “Local-Provision IPv4 Address Pool Config” Tab

On the “Local Provision IPv4 Address Pool Config” sub-tab, the following settings can be configured:

7

8

9

Download CM Config

Opens a dialog box to select a CM Config file to download from 

the CMTS for editing.

CM Profile:

 Select <cm.cfg OR cm30.cfg> allows user to 

select which config file to download, The DOCSIS 2.0 or 

DOCSIS 3.0 config file.
Submit: submit selection for download
Cancel:

 cancel download and close dialog box

Figure 6.1c - “Download CM Config” Prompt

1

2

3

Figure 6.2 - “Local-Provision IPv4 Address Pool Config” Tab

1

2

3

Summary of Contents for BT-CMTS Series





















Reviews: