background image

6

TRANSPORTATION AND STORAGE:

PROPANE GAS IS HEAVIER THAN AIR, AND WILL COLLECT IN
LOW AREAS, INCREASING THE ABOVE RISKS. THEREFORE:

• 

ALWAYS

use the cylinder cap provided with your cylinder

whenever the cylinder is not connected to your barbeque.
(Figure 4)
• 

DO NOT

store in a building, garage or any other enclosed

area. Store in a well-ventilated area.
• 

DO NOT

store near any gas burning apparatus or in any high-

heat areas such as a closed car or trunk.
•  Transport and store the cylinder in an upright position – do
not tip on its side.
•  Store out of reach of children. 
• 

DO NOT

smoke while transporting a cylinder in your vehicle.

•  Never fill a cylinder beyond 80% full : a fire causing death or
serious injury may occur
•  An over filled or improperly stored cylinder is a hazard due to
possible gas release from the safety relief valve. This could
cause an intense fire with risk of  property damage, serious
injury or death.
• If you see, smell or hear gas escaping, immediately get away
from the LP cylinder/appliance and call your fire department.
•  Never store a spare LP cylinder under or near the appliance or
in an enclosed area. 
• Do not store a spare LP cylinder under or near a barbecue
grill, or other heat sources, 
• Do not move the BBQ/grill when operating or while BBQ/grill
is hot.
• Never store or transport the LP cylinder where temperatures
can reach 125 F.
• Do not leave an LP cylinder in a car on a hot day.
• Do not use a damaged LP cylinder.  Dented or rusty LP
cylinders or LP cylinders with a damaged valve may be
hazardous and should be replaced with a new one immediately

.

.

ALTHOUGH IT IS SAFE WHEN USED

PROPERLY, CARELESS HANDLING OF THE

PROPANE GAS CYLINDER COULD RESULT IN

FIRE, EXPLOSION, AND/OR SERIOUS INJURY. 

WARNING

!

DANGER

NEVER STORE A SPARE LP CYLINDER

UNDER OR NEAR THE APPLIANCE OR IN

AN ENCLOSED AREA.

!

WARNING

!

FILLING:

FOR SAFETY REASONS, IF AN
OPTIONAL L.P. GAS CYLINDER
WAS SUPPLIED WITH YOUR
BARBEQUE, IT HAS BEEN
SHIPPED EMPTY. THE CYLINDER MUST BE  PURGED OF AIR
AND FILLED PRIOR TO USING ON YOUR BARBEQUE. WHEN
GETTING YOUR CYLINDER FILLED:

•  Allow only a qualified L.P. gas dealer to fill or repair your
cylinder.
• 

DO NOT

allow the cylinder to be filled beyond 80% full. 

•  Make sure the L.P. gas dealer checks the cylinder for leaks

after filling.

CYLINDER 
CAP

RETAINER
STRAP

LP TANK
VALVE

Fig. 4

NEVER OPERATE GRILL WITH LP

CYLINDER OUT OF CORRECT POSITION

SPECIFIED IN ASSEMBLY INSTRUCTIONS.

WARNING

!

ALWAYS CLOSE LP CYLINDER VALVE AND

REMOVE COUPLING NUT BEFORE

MOVING LP CYLINDER FROM SPECIFIED

OPERATION POSITION.

DANGER

!

Do not insert any tool or foreign object

into the valve outlet or safety relief

valve. You may damage the valve and

cause a leak. Leaking propane may

result in explosion, fire, severe personal

injury, or death.

Summary of Contents for FG50069










































Reviews: