manualshive.com logo in svg

Blue Giant BGL-22, Owner'S Manual

The Blue Giant BGL-22 Owner's Manual is vital for understanding how to use this powerful product effectively. Download the free manual from 88.208.23.73:8080 to unlock the full potential of your Blue Giant BGL-22. Ensure proper operation and maintenance with detailed instructions at your fingertips.

Share
Download
background image

7.

Position the new switches and four springs (4) in
bracket (5) and secure with two pins (6).

8.

Position switch assembly (1) in cover (17) and
secure with pin (6).

9.

Install the cap assembly as described in para-
graph 

5-1.2.

5-1.9. Tilt Switch Replacement.

1.

Remove the cap assembly as described in para-
graph 

5-1.1.

2.

Remove switch assembly (1A, 

Figure 5-4

) form

cap (17).

3.

Remove pin (6) securing bracket (9) and remove
the bracket.

4.

Remove two pins (6), two switches and four
springs (4) from bracket (9).

5.

Unsolder harness from defective switch.

6.

Solder the harness to new switch.

7.

Position the new switches and four springs (4) in
bracket (9) and secure with two pins (6).

8.

Position switch assembly (1A) in cover (17) and
secure with pin (6).

9.

Install the cap assembly as described in para-
graph 

5-1.2.

5-2. STEERING ARM

5-2.1. Return Spring Replacement.

The steering arm gas return spring (3, 

Figure 5-2

) is

replaced while the steering arm (2) is in the upright
position.
1.

Turn off the key switch (6, 

Figure 12-22

) and dis-

connect the batteries.

2.

Remove two screws (4, 

Figure 12-6

) and middle

cover (5).

3.

Secure the steering arm (2, 

Figure 5-2

) in the

upright position.

4.

Remove screw (4) and free the gas return spring
(6) from bracket (17).

5.

Pull downward on the gas return spring (3) to free
it from its seat inside steering arm (2).

6.

Position the new gas return spring (3) inside the
steering arm being sure it fully engages its seat.

7.

Position the opposite end of the gas return spring
(3) on bracket (17) and install screw (4).

8.

Install middle cover (5, 

Figure 12-6

) and secure

with two screws (4).

9.

Reconnect the batteries and turn on the key
switch (6, 

Figure 12-22

).

5-2.2. Steering Arm Removal.

1.

Turn off the key switch (6, 

Figure 12-22

) and dis-

connect the batteries.

2.

Remove two screws (4, 

Figure 12-6

) and middle

cover (5).

3.

Disconnect harness (28, 

Figure 5-2

) from harness

(1, 

Figure 12-25

).

4.

Attach a hoist to steering arm (2, 

Figure 5-2

).

5.

Remove screw (9), shaft (5) and the steering arm
(2).

5-2.3. Steering Arm Installation.

1.

Position steering arm (2, 

Figure 5-2

) over the

bracket (17) and secure with shaft (5) and screw
(9).

2.

Reconnect harness (28) from harness (1, 

Figure

12-25

).

3.

Install middle cover (5, 

Figure 12-6

) and secure

with two screws (4).

4.

Reconnect the batteries and turn on the key
switch (6, 

Figure 12-22

).

5-3. COMPARTMENT COVERS

5-3.1. Removal.

1.

Turn off the key switch (6, 

Figure 12-22

) and dis-

connect the batteries.

2.

Remove two screws (4, 

Figure 12-6

) and middle

cover (5).

3.

Remove two screws (1), washers (2) and upper
cover (3).

4.

Remove lower cover (6).

5-3.2. Installation.

1.

Install lower cover (6, 

Figure 12-6

).

2.

Install upper cover (3) and secure with two screws
(1).

3.

Install middle cover (5) and secure with two
screws (4).

4.

Reconnect the batteries and turn on the key
switch (6, 

Figure 12-22

).

40

Summary of Contents for BGL-22



































































































































Reviews:

No comments

Related manuals for BGL-22

HELI H2000 Series Manual preview
H2000 Series
Brand: HELI Pages: 111
JLG 25AM Service And Maintenance Manual preview
25AM
Brand: JLG Pages: 93

Brands by name

Popular brands

Load more brands