Ion
Press
this
button
to
anion air purifying function,indicator light green.
Full water indicator light
When water tank is full,indicator light shows red.Please empty the water tank
and back water tank back in correct place.
Humudity and timi ng indicator light
The
indicator
light
has
following
function
.
1.
When
power cord is connected, it shows
- - ，
enter
into
standby mode
.
2.When press the power button,shows
ambient humidity.
3.
When set a humidity, then shows the select humidity.
4.W
hen set a time to power on/off, will show set time period
.
5.
When press timmer button above 4 seconds,will show ambient temperature.
6.
When
ambient
temperature
< 5℃ ,
will
show
"CL"
.
7.
When
ambient
temperature
> 38℃,
will
show
"CH"
.
8.
When
ambient
humidity
< 20%RH
,will
show
"LO"
.
9.
When
ambient
humidity
> 92%RH ,
will
show
"HI"
.
10.
When temperature and humidity sensor failure, it will show
"E1".
O p e r a t i ng I nstructions
Once plu g in,ha ve buz zer beeping ,initia l st at e is 5 0% RH ,lo w wind spe ed.
Pres s th e power butto n to start work ,e nter n ormal d eh umidifi cation mode,
can adju st humi di ty and wind spe ed if need ed.
1.
Po w e r
on
2 .
Power
off
Press
power
button
to
stop
working,can not unplug power cord directly.
Water
tank
drainage
Water tank capacity is 8.2L,when reach full water level,full water indicator
light turn to green.Then the unit automatic stop work,buzzer buzzes 15 times to
warning users,that water in the tank must be emptied.
Water
tank emptied
：
1.
2.
Empty
the water in tank.
2
.
Clean water tank with cold water or warm water, do not use detergent, steel
wool, dust cloth, gasoline, benzene, diluent or other solvents to clean tank.
May damage the water tank and cause a leakage.
3 .
W h e n i n s t a l l w a t e r t a n k , p r e s s i t t i g h t l y . I f t a n k i s n o t p l a c e d p r o p e r l y ,
f u l l w a t e r s e n s o r w i l l a l a r m , t h e u n i t w i l l n o t w o r k .
Continuous water drain
The unit have a
11~12mm)
to
outlet water as following.
1.
Remove the rubber blocklet.
2.Insert plastic pipe into the drainage.
3.
Take out water tank,put rubber blocklet into water tank drain as image
③,
then
install
the
water
tank
.
continuous water drainage,use a plastic pipe(dia.
1
2
3
Automatic
water drain
The unit have
Use
a
water
pipe
length
less
than
6m,dia.6mm,insert into the auto
water drainage.(drainage
divide can't exceed 6 meters. drainage
height should lower than the machine),the steps as following.
1.
Remove the rubber blocklet in auto water drainage.
2. Insert water pipe into the drainage.
3.
Take out water tank,put rubber blocklet into water tank drain as image
③,
then
install
the
water
tank
.
4. Press the auto water drain button.
automatic
water drain function.
1
2
3
3.
Non-volatile memory
The system has automatic memory function,when it suddenly power off during
operation,will start work auto when power on,do not need to press power button.
Ion
Full water
Press the water tank on both sides,then pull the water tank out.
Notes
1.Do not remove the float in the water tank,make water full sensor will not
work,cause the machine unable to work properly .
