background image

Step 6: FIT & SECURE 

LOWER HANDRAILS 

6.1

6.2 

6.3 

IN 

LINE 

6.6 

Identify the lower RIGHT & LEFT handrails (small stamp in parts - Detail 6.1). Note: both the 
lower left handrails have holes in the center; the holes are for connecting the gate in a later 
step. Facing  step as if the climb, position right handrail on the right side and left on the left 
side. The lower handrails are to be positioned on the inside of the bolt flanges of the stringers 
and  upper  handrails.  Align  the  bolt  flanges  on  the  handrails  with  the  bolt  flanges  on  the 
stringers  and  upper  handrails  (see  Detail  6.2-6.5).  When  securing  with  hardware,  it  is 
important  to  start  with  the  connection  point  with  the  upper  handrail  (Detail  6.3).  With  the 
lower handrail on the inside of the bolt flange, align bolt holes by sliding the upper handrail up 
or down (Detail 6.3). Once aligned, make certain the upper and lower handrails are perfectly 
aligned (Detail 6.6). Secure connection using 3/4" bolt, washer both sides and nut. Repeat for 
all  connection  points  on  all  lower  handrails  at  all  bolt  flanges.  After  all  handrails  secured, 
secure upper handrails with step stringers using same hardware (Detail 6.7). Drill a 5/16" hole 
if bolt holes do not perfectly align. Repeat for all upper handrails and stringers 

Step 5: ASSEMBLE 

AND FIT UPPER 

HANDRAILS 

Identify the upper RIGHT (R) & LEFT (L) handrails (small stamp in parts - see Detail 
5.1 & 5.2). Fit handrail pair together as shown in Detail 5.3 - 5.5 aligning bolt holes at 
top.  Secure  using  1"  bolts,  washers  both  sides  and  nuts.  Tighten  hardware.  Repeat 
for  both  sets  of  upper  handrails.  Identify  the  top  platform  and  with  the  anti-skid 
surface facing up, fit the handrail pairs through the platform as shown in Detail 5.6 & 
5.7. NOTE: it is important that the correct handrails (L & R) fit through the holes in 
the platform as indicated. Slide the handrails up the handrail pairs. Fit the assembled 
handrails pairs & top platform into the top openings of each step system (see Detail 
5.8 & 5.9). Make certain they are positioned properly. DO NOT secure with hardware 

5.1

5.2 

5.3 

RIGHT 

LEFT 

5.4 

5.5 

5.8 

5.9 

6.4 

6.5 

6.7 

5.7 

5.6 

Blue Wave Products, Inc.

 

1745 Wallace Ave, Suite B

 

Saint Charles, IL 60174

Toll Free: 1-877-977-6010

Summary of Contents for NE1415W










Reviews: