background image


 

 
 

Fig 2 

 

Testing:  

Test the light before installation ensuring that you use the correct voltage and the light is illuminated 
correctly. 
After installation ensure again that the light is illuminated correctly before the boat goes back into 
the water and you remove the lens label. 
After you boat goes back into the water check internally for water tightness around where the light is 
installed. 
The light has internal indicator Led’s for fault finding, these are as follows: 

 

Over voltage will flash red.(check the voltage to the light) 

 

Under voltage will show a constant red. (check the voltage to the light) 

 

Over temperature will show amber.(allow the light to cool down and check if submerged) 

Maintenance:  

Regularly check the installation for water tightness 
Only clean the light with a soft bristle brush 

Warranty:  

Your product has a 2 year limited warranty for manufacturing defects. 
For any warranty issues please contact your point of sale retailer or go to 

www.bluefinled.com

 for 

further advice. 
Do not attempt to disassemble the light without Bluefin LED advice.

 

Installer please ensure that the SERIAL NUMBERS of the lights are written below and the 
manual is handed over to the end user. 
Please make a note of the serial numbers of the lights here. 
SERIAL NUMBERS 

  

 

 

 

 

 

          

 

Bluefin 

LED

 

Cottage Farm, Cottage Lane, 
Norton Juxta Twycross, Atherstone. CV9 3QH

   

       

Sales - Tel: 07950 909048      

 Email:

   

simon.steadman@bluefinled.com

 

Service - Tel: 01827 880450                                Email:

   

mark.branson@bluefinled.com

 

Administration - Tel: 01827 880450 

 Email:

   

samantha.barrie@bluefinled.com

 

Registered Address:

 

Square Rig Limited, t/a Bluefin LED, Cottage Farm, Cottage Lane, Norton Juxta Twycross, Atherstone, CV9 3QH 

Company Registration Number:

 08871451  

VAT Number: 179 2690 64

 

 

Bluefin Led Underwater lights. 

LM48CC Driver Installation manual. 

Thank you for choosing Bluefin LED underwater lights, our products have been designed and tested 
rigorously to ensure the optimum performance and longevity. 

Please ensure that your product is installed as per our instructions below, failure to do so may 
invalidate your warranty.  

Summary of Contents for GW16IFM









Reviews: