BluePoint Fasteners BP-27C Instruction Manual Download

Page: 11 / 13

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE

POSSIBLE REMEDIES

Tool does not
fire

•

Failure to depress
completely

•

Excessive dirt
buildup on breech
face not allowing
proper penetration
of firing pin

•

Firing pin and/or
firing pin assembly
damaged

WARNING
Never attempt to pry a
cartridge from the tool

•

See “Tool does not
completely depress”

•

After following misfire
procedure, check firing
pin indentation on load.
Clean breech face.

•

Replace damaged parts

If the problem continues:

•

Contact Bluepoint
distributor

Overdriving of
fasteners

•

Excessive power

•

Soft base material

•

Use lower power level
load color and number

•

Check the base material

If the problem continues:

•

Contact Bluepoint
distributor

Tool does not
completely
depress

•

Incorrectly
assembled or
damaged parts

•

Check all parts for
damage and assemble
correctly

If the problem continues:

•

Contact Bluepoint
distributor

Reduction or
loss of power

•

Piston is not
returning to the full
rear position

•

Worn or damaged
piston

•

Disassemble and clean
Barrel, Piston, Fastener
Guide and re-assemble

•

Replace damaged piston

If the tool cannot be
disassembled :

•

Contact Bluepoint
distributor

Strip does not
advance

•

Strip not inserted in
tool correctly or is
damaged

•

Damaged indexing
mechanism

WARNING
Never attempt to pry a
cartridge from the
magazine strip or tool

•

Check load strip. Properly
dispose of damaged strip

•

Contact Bluepoint
distributor

Tool fails the
Daily Function
Test

•

Contact Bluepoint
distributor

13-1

13-2

13-3

13-4

BP-27C TOOL SCHEMATIC

S/N

Item No.

Part Name

BP27C-01

Spall guard

BP27C-02

Guide Nut

BP27C-03

Nosepiece

BP27C-04

Piston

BP27C-05

Barrel

BP27C-06

Barrel Spring

BP27C-07

Housing Assembly

BP27C-08

Advance Lever Spring

BP27C-09

Advance Lever Pin

BP27C-10

Advance Lever

BP27C-11

Firing Pin Assembly Spring

BP27C-12

Firing Pin Housing

BP27C-13

Firing Pin Assembly

BP27C-13-1

Braking Pin

BP27C-13-2

Firing Pin

BP27C-13-3

Braking Pin Spring

BP27C-13-4

Jacket

BP27C-14

Locking Sleeve

BP27C-15

Firing Pin Spring

BP27C-16

Connecting Tube

BP27C-17

Pole Connector

Summary of Contents for BP-27C














Search results

Summary of Contents for BP-27C

Reviews:

Related manuals for BP-27C

Brands by name

Popular brands

BluePoint Fasteners BP-27C, Instruction Manual

Search results

Summary of Contents for BP-27C

Reviews:

Related manuals for BP-27C

Brands by name

Popular brands