17
■ When not in use, the Nailer, fuel cell and battery
should be stored in a warm and dry place.
■ Keep it out of reach of children.
4
. WARNING LABEL
Change the WARNING LABELifmissingordamaged.
A new WARNING LABEL is available from a
dealer authorized service center.
5
. Maintenance chart
6
. Operator troubleshooting
See page 18.
CAUTION
Repair, modification and inspection of The
Power Tools must be carried out together with
the replacement parts listed by a dealer
Authorized Service Center.
In the operation and maintenance of power tools,
the safety regulations and standards prescribed
in each country must be observed.
MODIFICATIONS:
The Power Tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts (i.e. code numbers and/or
design) may be changed without prior notice.
SERVICE AND REPAIRS
WARNING
■
Only service personnel trained by dealer,
distributor or employer shall repair the Nailer.
■
Use only parts supplied or recommended by
dealer for repair.
All quality Nailers will eventually require servicing
or replacement of parts because of wear from normal
use.
NOTE
Specifications are subject to change without any
obligation on the part of dealer.
ACTION
WHY
HOW
Clean magazineand
feeder mechanism.
To prevent a jam.
Daily cleaning.
Keep firing head
working properly.
To promote operator
safety and efficient
Nailer operation.
Daily cleaning.
Make sure all screws
are tightened.
To avoid damage to
Nailer and to ensure
safety.
Periodical
inspection.
MAINTENANCE
NOTE:
■ The information contained in thisManualisdesigned
to assist you in the safe maintenance of theNailer.
■ Some illustrations in this Manual may show details
or attachments that differ from those on your own
Nailer.
MAINTENANCE AND INSPECTION
Read section titled “SAFETY”.
DANGER
■
Never use and test in presence
of flammable liquids or gases.
■
Keep away from ignitionsource.
■
No smoking.
WARNING
Remove fuel cell, battery and all nails fromNailer
when:
Daily cleaning;
Maintenance and Inspection;
Clearing a jam.
1. Daily cleaning
Must regularly clean nailer, remove the internal
accumulation of smeary, carbon and dust, to
ensure the normal operation and to extend
nailer's working life. Please use dealer
designated cleaner (00091800).
Follow the attached Gas Concrete Nailer
Cleaning Guide - a steps and methods to clean
the nailer.
The nailer cleaning intervals depend on the
nailer operating environment and the firing
quantity per week of nails. If using in a dirty
environment and firing large quantity per week,
nailer cleaning intervals will be shorter.
Below is the cleaning time intervals form for your
reference. Depending on the usage, the cleaning
interval may be shortened or extended.
Note
After completion of cleaning, lubricate the
Nailer with with oil (00091600) as shown in
the attached “Gas Concrete Nailer Cleaning
Guide”.
If you have any questions about of the cleaning
operating procedures and methods, please contact
a dealer or an authorized service center.
2
. Inspecting the magazine
①
REMOVE FUEL CELL and BATTERY.
②
Clean the magazine.
Remove paper chips or wooden chips which
may have accumulated in the magazine.
③
Lubricate it with dealer designated lubricant oil.
CAUTION
Check that the nail feeder slides smoothly by
pulling it withfinger.
If not smooth, nails can be driven at an irregular
angle and hurt someone.
3. Storing
DANGER
■
Store Nailer properly withnails,
fuel cell and battery removed .
■
Thefuelcellisanaerosoldispensers
with flammable contents.
■
When not in use, the Nailer, fuel cell and
battery should be stored in tool case and in a
dry place and below temperature 122°F (50°C).
■
Store indoors at temperature 41°F (5°C)
～
77°
F
（
25°C
）
.
■ When not in use for an extended period, apply a
thin coat of the lubricant to the steel parts to avoid
rust.
■ Do not store the Nailer fuel cell and battery in a
very cold weather environment.
Cleaning time intervals form
Operation Environment
very dirty
dirty
common
clean
Firing quantity
per week
1000
2 Week
1 Month
2Month
4Month
2000
2 Week
1 Month
2Month
3Month
4000
2 Week
1 Month
1.5Month 1.5 Month
6000
2 Week
2 Week
1Month
1 Month
8000
2 Week
2 Week
1Month
1 Month
Cloth
16
