background image

507867-02

Page 36 of 55

Issue 1933

Figure 59. 

Condensate Trap with Optional Overflow 

Switch

Gas Piping

If  a  flexible  gas  connector  is  required  or  allowed  by 

the authority that has jurisdiction, black iron pipe shall 

be  installed  at  the  gas  valve  and  extend  outside  the 

furnace  cabinet.  The  flexible  connector  can  then  be 

added between the black iron pipe and the gas supply 

line.

 CAUTION

Do  not  exceed  600  in.-lbs.  (50  ft.-lbs.)  torque  when 

attaching the gas piping to the gas valve.

 WARNING

1.  Gas piping may be routed into the unit through either 

the left or right hand side. Supply piping enters into the 

gas valve from the side of the valve as shown in Figure 

61 and Figure 62. 

A low inlet pressure switch in LP/propane applications 

is recommended. 

 IMPORTANT

2.  When connecting gas supply, factors such as length 

of run, number of fittings and furnace rating must be 

considered to avoid excessive pressure drop. Table 9 

list recommended pipe sizes for typical applications.

NOTE: 

Use two wrenches when connecting gas piping 

to avoid transferring to the manifold.

3.  Gas  piping  must  not  run  in  or  through  air  ducts, 

clothes chutes, chimneys or gas vents, dumb waiters 

or elevator shafts. Center gas line through piping hole. 

Gas line should not touch side of unit. See Figure 61 

and Figure 62.

4.  Piping should be sloped 1/4 “ per 15 feet (6 mm per 5.6 

m) upward toward the gas meter from the furnace. The 

piping must be supported at proper intervals, every 8 

to 10 feet (2.44 to 3.05 m), using suitable hangers or 

straps. Install a drip leg in vertical pipe runs to serve as 

a trap for sediment or condensate.

5.  A 1/8” N.P.T. plugged tap or pressure post is located 

on the gas valve to facilitate test gauge connection. 

See Figure 60.

6.  In some localities, codes may require installation of a 

manual  main  shut-off  valve  and  union  (furnished  by 

installer)  external  to  the  unit.  Union  must  be  of  the 

ground joint type.

Compounds used on threaded joints of gas piping must 

be resistant to the actions of liquified petroleum gases.

 IMPORTANT

Leak Check

After  gas  piping  is  completed,  carefully  check  all  piping 

connections (factory and field installed) for gas leaks. Use 

a leak detecting solution or other preferred means.

Never use an open flame to test for gas leaks. Check all 

connections using a commercially available soap solution 

made specifically for leak detection.

The furnace must be isolated from the gas supply system 

by closing its individual manual shut-off valve during any 

pressure  testing  of  the  gas  supply  system  at  pressures 

more than or equal to 1/2 psig (3.48 kPa, 14 inches w.c.).

Figure 60. 

Summary of Contents for BG921-E
























































Reviews: