bluMartin freeAir100 Service Download

Page: 4 / 18

Service

[ S ] 35

DIP Switches

Room Extract

/h)

In case of 2

Room Extract option (= 4

flap) this will allow

the user to deactivate the hourly switch of extract air from 2

to1

room.

This makes sense in case your freeAir100 is installed inside

e.g. a closet.

Note

The deactivation is possible only when the 2

Room Extract

is adjusted to 100 m³/h.

This feature is only available in devices with a serial number

of 3000 or higher.

Room Extract

/h)

The additional 2

Room Extract module enables adjustment of max air flow of ventilation for

exhaust of the 2

room. Diameter, length and number of turns in the ducting as well as air inlet

size limit the air stream (see table above):
• off: No exhaust ducting installed or extract opening blocked
• 30: One flex-duct connected (with extract valve



125)

• 60: Two flex-ducts installed (with extract valve



125 and completely open)

• 100: Three flex-ducts or spiral-seam pipe DN100 installed (with extract valve



200)

Note

Incorrect adjustment or high air friction coefficient will lead to higher noise level and premature

filter error warning.

Summary of Contents for freeAir100



















Search results

Summary of Contents for freeAir100

Reviews:

Related manuals for freeAir100

Brands by name

Popular brands

bluMartin freeAir100, Service

Search results

Summary of Contents for freeAir100

Reviews:

Related manuals for freeAir100

Brands by name

Popular brands