35
EN
ignition attempts for gas to dissipate.
Failure to do this may result in flame roll out beyond the emitter grid.
Note: it is possible to light the appliance using a long match, by lighting the
burner through the ignition hole provided.
4. When the pilot is lit keep knob pressed for up to 20 seconds to heat the
thermo-couple flame sensor, then release it (first ignition generally takes
more time, because the gas circuit is full of air).
5. If the pilot does not stay lit, repeat steps 2 - 4.
6. Turn knob to LOW position.
7. Adjust the heat input by turning the knob from the LOW position, to the
HIGH position, as required.
8. After lighting, turn knob from LOW to HIGH, position and back, to check
flame stability.
9.
In case of accidental break down of the flame (due to wind or other
reasons), a Flame Safely Device (FSD) will automatically shut-off gas
supply within 90 seconds.
Flame Characteristic
The flame pattern at the emitter screen should be visually checked whenever
heater is operated.
If black soot is accumulating on the emitter grid or reflector, the heater should
be turned off immediately. The heater should not be operated again until the
unit is serviced and or repaired.
OPERATION
Note: The burner may be noisy when initially turned on, To eliminate excessive
noise from the burner, turn the control knob to the LOW position. Then, turn
the knob to the level of heat desired.
When heater is ON:
Emitter grid will become bright red due to intense heat. The colour is more
visible at night. Burner will display tongues of blue flame. These flames should
not produce thick black smoke, indicating an obstruction of airflow through
the burners.
Operation pressure checked:
If the flame is very small, this is because the supply pressure is not enough.
Please refill gas cylinder.
Summary of Contents for 10033278
