background image

F2 Full Face Mask User Manual V2.1

 

2

 / 

14

 

E

n

g

lis

h

 

Before Using the Mask 

 

WARNINGS

 

 

The vent holes must be kept clear. 

 

Explanation  of  Warning:

  CPAP  systems  are  intended  to  be 

used with special masks with connectors which have vent holes 
to allow continuous flow of air out of the mask. When the CPAP 
machine is turned on and functioning properly, new air from the 
CPAP machine flushes the exhaled air out through the attached 
mask exhalation port. However, when the CPAP machine is not 
operating,  enough  fresh  air  will  not  be  provided  through  the 
mask,  and  exhaled  air  will  be  rebreathed.  Rebreathing  of 
exhaled  air  for  longer  than  several  minutes  can,  in  some 
circumstances,  lead  to  suffocation.  This  warning  applies  to 
most models of CPAP systems. 

 

At low CPAP pressures the flow through the exhaled port may 
be  inadequate  to  clear  all  exhaled  gas  from  the  tube.  Some 
rebreathing may occur.   

 

To minimize the risk of vomiting during sleep, the patient should 
avoid eating or drinking for three hours before using the mask. 
This  mask  is  not  recommended  if  the  patient  is  taking  a 
prescription drug that may cause vomiting.   

 

Do  not  use  the  mask  without  the  Non-Rebreathing  Valve  in 
place. 

 

This  mask  should  not  be  used  on  patients  who  are 
uncooperative,  obtunded,  unresponsive,  or  unable  to  remove 
the mask. 

 

Follow all precautions when using supplemental oxygen. 

 

Oxygen flow must be turned off when the flow generator is not 
operating,  so  that  unused  oxygen  does  not  accumulate  within 
the flow generator enclosure and create a risk of fire.   

 

At  a  fixed  flow  rate  of  supplemental  oxygen  flow,  the  inhaled 

Summary of Contents for BMC-FM2

















Reviews: