LAN-AD16f
Page 10
7
Important notes for using the LAN-AD16f
•
The device is only suitable for extra-low voltages - please observe the relevant regulations! For reasons relating to
EMC, it must only be used in closed PC housings. ESD voltages at open lines may cause malfunction. Only use an
electrical isolated power supply unit (with CE).
•
Only use non-solvent detergents for cleaning. The product is designed to be maintenance-free.
•
Signal cables are connected at the two 37-pin D-Sub female connectors – preferably use shielded cables. For best
possible interference suppression, connect shield at one end only. Close open inputs if necessary.
•
The gain is adjusted to even values. Therefore, only 64000 values (for 16 bit) of the full range of the converter are
used. As a result, the measuring ranges are slightly larger (e.g.
±
10.24V) than the indicated measuring ranges so
that overranges can be recognized.
•
The device must not be used for safety-relevant tasks. With the use of the product, the customer becomes manu-
facturer by law and is therefore fully responsible for the proper installation and use of the product. In the case of
improper use and/or unauthorized interference, our warranty ceases and any warranty claim is excluded.
Do not dispose of the product in the domestic waste or at any waste collection places. It has to be either duly dis-
posed according to the WEEE directive or can be returned to bmcm at your own expense.
8
Technical data
(typical at 20°C, after 5min., +12V supply)
•
Analog inputs
Channels // Resolution:
16 analog inputs (single-ended) // 16 Bit
Sampling rate:
max. 250kHz total sampling rate*
Measuring ranges // Noise:
±
10V //
±
5 LSB
±
5V //
±
7 LSB
±
2V //
±
8 LSB
±
1V //
±
8 LSB
Surge protection:
±
35V (when turned on),
±
20V (when turned off), max.
±
20mA in total of all input channels!
Memory depth:
only depending on the size of the hard disk of the server PC
Input resistance // Input capacity:
1M
Ω
(with PC turned off: 1k
Ω
) // 5pF
Zero shift // Gain drop:
±
50ppm/
°
C //
±
50ppm/
°
C
Frequency accuracy // Frequency drift:
max.
±
100ppm // max.
±
50ppm/
°
C
* The total sampling rate is the sum of the sampling rates of the individual used channels (e.g. if 5 channels are scanned with 50kHz, the total
sampling rate adds up to 250kHz).
The values for accuracy always relate to the respective measuring range. Errors might add at worst.
•
Analog outputs
Output range // Output current:
2 voltage outputs with
±
10V // 1mA max.
Resolution // Accuracy:
16 bit // typ. 1mV
Zero shift // Gain drop:
±
50ppm/
°
C //
±
50ppm/
°
C
•
Digital channels
Channels:
16 Digital IN, 16 Digital OUT
Counter:
19-bit counter, up/down counter, or incremental encoder; connect at digital pins
Level:
CMOS/TTL compatible (low: 0V..0.7V; high: 3V..5V)
Resistance R
i
// Output current:
Digital IN: 10k
Ω
, Digital OUT: 1k
Ω
// 0.5mA
•
General data
Power supply:
+9..40V DC, typ. 3W, max. 5W (electr. isolated by DC/DC converter in the device) at 3-pin DIN plug
Connections analog // digital:
all channels at a 37-pin D-Sub female at the device back // front
LAN connection:
Twisted Pair RJ45 socket, 100Mbit
CE standards:
EN61000-6-1, EN61000-6-3, EN61010-1; for decl. of conformity (PDF) visit
ElektroG // ear registration:
RoHS and WEEE compliant // WEEE Reg.-No. DE75472248
Max. permissible potentials:
60V DC acc. to VDE
, max. 1kV ESD on open lines
Temperature ranges // Relative humidity:
operating temp. -25..50
°
C, storage temp. -25..70
°
C // 0-90% (not condensing)
Dimensions // Protection type:
167 x 113 x 30 mm
3
// IP30
Delivery:
device in aluminum housing, 3-pin DIN connector, "Software Collection" CD, description
Available accessories (optional):
power supply unit ZU-PW10W, current shunt ZU-CS250R, gender changer ZU37SS,
connecting cables ZUKA37SB, ZUKA37SS, ZUKA10T (Twisted Pair), ZUKA-CL10T (Crosslink),
D-Sub plug ZUST37, 3-pin DIN socket ZU3DIN, connector boards ZU37BB/-CB/-CO,
DIN rail set ZU-SCHI, waterproof housing ZU-PBOX-LAN
Warranty:
2 years from date of purchase at bmcm, claims for damages resulting from improper use excluded
•
Software
Software on CD (included):
ActiveX Controls LIBADX (hardware independent) for programming on Windows
®
7/XP;
LIBAD4 SDK for C/C++ programming on Windows
®
7/XP, Mac OS X, Unix (FreeBSD, Linux);
trial version of the measuring software NextView
®
4 to test and operate the hardware;
configuration software LAN-Admin
NextView
®
4 (optional):
professional software (versions: Professional, Lite) for the acquisition and analysis of measurement
data on Windows
®
7/XP
Manufacturer: BMC Messsysteme GmbH. Subject to change due to technical improvements. Errors and printing errors excepted. Rev. 1.1
05/22/2013
