background image

BMG Imports

Sliding Gate Opener

MODEL No. LW550

Power rating: 220-240v AC 50Hz 550w

Duty Close: 0-120 adjustable Max. 30s open

Max. gate weight 1500kg

Motor rotational speed 1400rpm

Output rotational speed 46.6r/min

Approval No. SAA121472

45° C ~+ 55° C IP44 Made In China

Important Safety information 

Sliding Gate Motor - Model 550 AC Sliding

This item must be installed by a qualified electrician

All safety instructions and insallation methods should be read and completely 

understood by the installer and the owner prior to the installation of the gate 

opener system.  This product is designed and manufactured for the use indicated in 

this document.  Remember that all automatic gates are intended for vehicular gates 

only.  A separate gate or entrance must be installed for pedestrian use.  Any other use, 

not expressly indicated may damage the product or be a source of danger.  Do not use 

it on large sized gates that have a steep incline.  Wrong selection of motor will result in 

unreliable operation.

Owner should observe the following:

1. Do not cross the gate while it is operating

2. Keep children away from the gate and the remote control

3. Do no adjust the setting of the control panel unless you understand what you are

doing

4. Learn the use of the the emergency override key.  This is crucial in the event that

the system does not work.

Installer should observe the following:

1. Make sure the gate weight does not exceed the maximum weight specified

2. The gate design must be suitable for the installation of the gate opener system

3. Ensure that the gate is installed on flat,level ground and can move and slide freely

in both directions along the entire gate length

4. Gate opener must be installed in the area where it is not easily damaged

5. Do not change with parts or components not supplied by the manufacturer

6. Make sure all wiring works are correct in accordance with electrical bylaws and in

good condition before supplying the mains power to the control panel

7. Turn OFF the power when doing any maintenance

8. Ensure the control panel box is free from water leakage and insects to avoid short

circuiting of the control panel and voiding warranty

9. Never supply mains power directly to the DC motor if cover is damaged

10. Do not install the operating system if in doubt.  Contact the manufacturer or your

local agent

1/1

1

Summary of Contents for LW550













Reviews: