background image

 

EN/4

 

Retrofit / Installation kit No. 82 83 0 140 507 

Issue date: 06.2001

Installation Instructions No. 01 29 0 140 511

 

2.

Preparations

 

0

 

Cars without an on-board monitor radio only:

TIS instruction

No.

 

Print out error memory
Disconnect the battery

1200

Remove the cover in the footwell on the driver’s side
Remove the A pillar trim on the driver’s side

51 43 201

Remove both door sill strips on the driver’s side

51 47 000

Remove the B pillar trim on the driver’s side

51 43 148

Remove the rear seat bench

52 24 005

Remove the left side section of the backrest
Remove both front door trims

51 41 000

Remove the speaker cover in the headlining at the rear (only the screws are 
to be reused)
Remove the boot floor cover or loading aid
Remove the wheel arch cover
Remove the radio

65 11 030

Remove the spare cover or the rail for the loading aid on the left next to the 
spare wheel trough
Remove the on-board tool kit holder and jack
Remove the left side section of the backrest

 

Cars with an on-board monitor radio only:

TIS instruction

No.

 

Print out error memory
Disconnect the battery

1200

Remove both front door trims

51 41 000

Remove the speaker cover in the headlining at the rear 
(only the screws are to be reused)
Remove the boot floor cover or loading aid
Remove the wheel arch cover
Remove the CD changer if necessary
Remove the spare cover or the rail for the loading aid on the left next to the 
spare wheel trough
Remove the on-board tool kit holder and jack
Remove the left side section of the backrest

Summary of Contents for E39/2






















Reviews: