BN BNR7231A User Manual Download

Page: 12 / 12

USER MANUAL ~ DRYWALL SANDER MODEL No. BNR7231A

- Page 12-

For your own safety, never remove parts or accessories of the electric tool during

operation. In case of fault or damage have the electric tool repaired only by a

specialist workshop or by the manufacturer.

10. IMPORTANT NOTES

For your personal safety, READ and UNDERSTAND before using.

Save these instruction for future reference

Always Wear Ear Protection With This Tool

Always Wear Eye Protection With This Tool

Always Wear a breathing Mask With This Tool

11 . ENVIRONMENTAL PROTECTION

Do not dispose of in general household waste. Instead dispose of in an

environmental way, contact your local recycling centre or council

and advice. Please take the care of the environment.

BN Products-USA, LLC.

3450 Sabin Brown Road

Wickenburg, AZ 85390

(800) 992-3833

(928) 684-2813

mail@bnproducts.com

www.bnproducts.com

Summary of Contents for BNR7231A













Search results

Summary of Contents for BNR7231A

Reviews:

Related manuals for BNR7231A

Brands by name

Popular brands

BN BNR7231A, User Manual

Search results

Summary of Contents for BNR7231A

Reviews:

Related manuals for BNR7231A

Brands by name

Popular brands