The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.
B-38030 r9/30/14 Intl. Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions.
© 2014 by Bobrick Washroom Equipment, Inc.
Heating elements heat air without hot spots — inaccessible to vandals.
Electronic Control —
Infrared emitter receiver sensor, activation sensor PCB that is connected by two shielded wires to the dryer PCB. The sensor
PCB is enclosed in a plastic housing and has an LED that flashes green when the dryer is ready, is solid green when the dryer is running and is solid
red when the dryer is not ready to run.
Air Management System —
Consists of two silicone ducts and two black plastic air nozzles attached to the cabinet below the towel tray.
OPERATION:
Paper towel dispenser is designed to dispense C-fold or multi-fold paper towels without use of additional adapters or towel trays. To service
waste bin, unlock lower door with key provided and remove waste container. Cable door-swing limiter prevents damage to washroom accesso-
ries and walls. Directed air nozzles shall prevent dryer from blowing into waste container. Dryer has no-touch operation. There are two modes
of operation, dryer promotion encourages use of dryer and paper promotion encourages use of paper towels. The unit is set in the factory to
dryer promotion. Infrared emitter receiver sensor monitors the activation zone. Sensor LED will turn green and flash when dryer is ready
for use. LED will turn red when dryer is not ready. When unit is set to dryer promotion, the dryer and green LED will turn on when hands
are held under air-outlet opening and across path of sensor. Remove hands from path of sensor and dryer stops. When the unit is set to paper
promotion, there is a 3 second delay before the dryer will turn on. Electronic control has automatic shutoff approximately 1-1/2 minutes after
dryer turns on if an inanimate object is placed in the activation zone. After inanimate object is removed, electronic control automatically resets
itself and dryer operates normally. Dryer motor will never be allowed to get hotter than 70°C in either mode.
SAFETY WARNING:
Installation and wiring must conform to current IEE Regulations for the UK and local or appropriate
regulations for other countries. Installation must be completed and supervised by a qualified
electrician. If the dryer in the unit fails or malfunctions, it should be disconnected from power and a
qualified electrician should be called. Do not remove the dryer cover to access internal components of
the dryer.
1-Year Limited Warranty —
This warranty is limited to the repair or exchange of defective dryer parts at the option of Bobrick. See
Installation Instruction Sheet, Form No. 38030-69, for full details.
INSTALLATION:
Provide framed rough wall opening 362mm (14-1/4") wide x 1412mm (55-9/16") high. Minimum recessed depth required from finish face of
wall is 100mm (4"). Allow clearance for construction features that may protrude into rough wall opening from opposite wall. Coordinate with
mechanical engineer to avoid pipes, vents, and conduits. If unit projects above top of wainscot, provide aluminum channel or other filler to
eliminate gap between flange and finish face of wall. Mount unit in wall opening with shims between framing and cabinet at all points indicated
by an S, then secure unit with 4.2 x 32mm (#8 x 1-1/4") sheet-metal screws (not furnished).
Dryer Wiring Instructions:
Connect ground wire to ground terminal marked and the 208-240-volt wires to terminal marked L1 and L2.
Notes:
Electronic sensor will detect movement within 100mm (4") of air-outlet nozzle. Use caution when choosing installation location.
Consider proximity to doorways and other traffic areas. For installation instructions that include step-by-step installation procedures and
details of electrical service connections, see Form No. 38030-69, which is packed with each shipment. This form is also available in advance
upon request.
SPECIFICATION:
Recessed Paper Towel Dispenser, Automatic Hand Dryer, And Waste Bin (3-in-1 unit) shall be type-304 stainless steel with all-welded
construction; exposed surfaces shall have satin finish. Doors shall be 1.2mm (18-gauge); have 14mm (9/16") 90° return edges; be secured
to cabinet with concealed, full-length stainless steel piano-hinges; and equipped with a stainless steel cable door-swing limiter and two flush
tumbler locks per door keyed like other Bobrick washroom accessories. Paper towel dispenser shall be capable of dispensing 600 multifold
or 450 C-fold paper towels. Unit equipped with TowelMate consisting of a 90° return towel guide angle inside cabinet to prevent paper towels
from falling forward out when door is opened for servicing and a Nylon Rod across the center of the towel tray to dispense paper towels one at
a time. Waste bin shall be furnished with a removable, leak-proof, rigid molded plastic waste-container with a capacity of 13.7 liters (3.6 gal.).
Directed air nozzles shall prevent dryer from blowing into waste bin. Hand dryer shall have a one-piece,18-8, type-304, 0.8mm (22-gauge)
stainless steel cover. Dryer mounting base shall be 1.5mm (20-gauge) plated steel with three 6mm (0.236") diameter mounting holes. Fan
housings shall be fire-retardant molded black plastic. Dryer shall be equipped with dual air outlets that run through two vertical ducts and
out the black plastic nozzles under the towel dispenser. Motor shall be 1/7 hp, universal type on resilient mounting with sealed ball bearing at
drive-shaft end and self-lubricating sleeve bearing at nondrive end; equipped with automatic thermal-overload switch. Heating elements shall
be located on outlet side of fan, shall heat air without hot spots, be inaccessible to vandals, and protected by an automatic thermal-overload
switch. The dryer will be controlled by the activation sensor which is part of the electronic control. The electronic control will never allow the
dryer motor to be hotter than 70°C. There are two modes of operation, dryer promotion and paper promotion. Dryer promotion mode, the
dryer shall turn on when hands are held under air-outlet opening and across path of sensor. Paper promotion mode, there will be a three (3)
second delay between seeing the hands and when the dryer turns on. Dryer shall turn off automatically when hands are removed. Sensor
shall automatically shut dryer off approximately 1-1/2 minutes after dryer turns on if an inanimate object is placed in activation zone. After
inanimate object is removed, electronic sensor shall automatically reset itself and dryer shall operate normally. The electronic control will
have an LED that will flash green when the dryer is ready, be solid green when the dryer is running and be solid red when the dryer is not
ready. Unit shall VDE approved, CE marked and cUListed. Unit shall comply with EU Directive "Restriction of Hazardous Substance" (ROHS)
requirements for non-use of certain hazardous substances in the production of electronic products. Unit shall be protected by a limited 1-year
warranty from date of purchase on all parts except motor brushes.
Recessed Paper Towel Dispenser, Automatic Hand Dryer, and Waste Bin (3-in-1 unit) shall be Model B-38030 of Bobrick
Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom
Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom
Equipment Limited, United Kingdom.
