BodyCraft LCS-4 Assembly Manual Download

Page: 21 / 28

154

205

154

147

121

206

209

121

153

146

147 134

212

147 134

104

145

152 147

128

210

211

203

204

145

123

146

207

153

124

146

201

152

147

134

202

129

127

147

127

147

154

145

147

146

153

146

105

LEG PRESS SYSTEM ASSEMBLY

1. Attach Leg Press Weight Base Connector (207) to Base Frame (1), using two 1/2" X 1-1/4" Hex

Bolts (169) and two 1/2" Washers (146). Cap two 50mm S.Q. Plugs (64) into Base Connector

(207).

2. Attach Long Leg Press Connector (205) into the Weight Base (5), using two 3/8" Washers (147)

and two 3/8" Nylon Nuts (154).

3. Attach Leg Press Main Frame (202) to Leg Press Weight Base Connector (207) and Long Leg

Press Connector (205), using two 3/8" X 4-1/4" Hex Bolts (127), four 3/8" Washers (147) and two

3/8" Nylon Nuts (154).

4. Attach Base Stabilizer (201) to Leg Press Main Frame (202) using two 1/2" X 3-1/4" Hex Head

Bolts (123) and two 1/2" Nylon Nuts (153). Attach 45 X 75mm Rect. Cap (61) to rear of Leg

Press Main Frame (202) and two 50mm SQ. Caps (62) to Base Stabilizer (201).

5. Slide Axle on Rear Leg Press Support (209) into each Bearing Housing (70), then attach Bearing

Housings (70) back onto Leg Press Main Frame (202), using four 1/2" X 1-3/4" Hex Bolts (124),

eight 1/2" Washers (146) and four 1/2" Nylon Nuts (153). Attach Front Leg Press Support (206)

to Leg Press Main Frame (202) using one 5/8" X 6-1/2" Hex Head Bolt (121), two 5/8" Washers

(145) and one 5/8" Nylon Nut (152).

6. Attach Foot Plate Connector (210) to Rear Leg Press Support (209) and Front Leg Support (206)

using one each 5/8" X 6-1/2" Hex Head Bolt (121), two 5/8" Washers (145) and one 5/8" Nylon

Nut (152).

7. Attach Foot Plate (211) to Foot Plate Connector (210), using two 1/2" Washers (146) and two

1/2" Nylon Nuts (153). Attach 45 X 75mm Rect. Plugs (63) to Foot Plate (210). Attach Right &

Left Leg Handles (203 & 204) to Leg Press Main Frame (202), angle facing up, using

two 3/8" X 3-1/8" Hex Head Bolts (128), four 3/8" Washers (147) and two 3/8"

Nylon Nuts (154). Attach Seat Pad (105) to Leg Press Main Frame (202),

using two 3/8" Washers (147) and two 3/8" X 1" Hex Head Bolts

(134), one 3/8" X 2-3/4" Hex Head Bolt (129). Attach Back Pad (104)

to Back Pad Adjuster (212) using two 3/8" Washers (147) and two 3/8"

X 1" Hex Bolts (134). Slide Back Pad Adjuster (212) into Leg Press

Main Frame (202) by pulling pre-installed Locking

Spring Knob (79).

Tighten all the bolts and nuts gradually, from

ground - up.

Summary of Contents for LCS-4





























Search results

Summary of Contents for LCS-4

Reviews:

Related manuals for LCS-4

Brands by name

Popular brands

BodyCraft LCS-4, Assembly Manual

Search results

Summary of Contents for LCS-4

Reviews:

Related manuals for LCS-4

Brands by name

Popular brands