17
During the Heart Rate Control or Weight Loss program, you can change the speed or elevation by pressing the Speed or Elevation INCREASE or
DECREASE keys. Keep in mind that the computer will then gradually readjust the speed and/or elevation to compensate for the change in speed
or elevation you made by gradually bringing your ACTUAL heart rate near the TARGET heart rate level.
WARNING –
If you feel that the running belt is moving too fast for your fitness level and you cannot keep up, press the CLEAR/STOP key and
terminate the exercise program. You can try the program again, but at a lower INTENSITY level (60%). If this is still too fast for you, do not use
the Heart Rate Control program until your fitness level allows you to safely exercise at your TARGET heart rate level.
During the exercise, the main computer screen will show a speed or elevation profile like the other programs, but will display your ACTUAL heart
rate and your TARGET heart rate on the message center. Once the exercise has started, your ACTUAL heart rate should be lower than the
TARGET heart rate. The computer then will gradually regulate the speed and elevation simultaneously to increase your exercise intensity level,
resulting in a higher ACTUAL heart rate.
Your heart rate will be displayed on the message center as ACTUAL heart rate and TARGET heart rate (T). For example: HRATE 110/115T.
NOTE–
You can change your target heart rate while in the program by pressing the JustGo
TM
/ENTER key and modify it by using the
Speed DECREASE or INCREASE keys and by pressing the JustGo
TM
/ENTER key to accept it.
Walk Program
The Walk program allows you to create your own exercise as you progress in the program. The speed and elevation are completely controlled by
the user at all times. At a glance, Manual and Walk programs seem very similar due to the fact that the user controls both the speed and
elevation at all times. The difference is that in the Walk program, you can’t go over 4.0 MPH (6.4 KM/H) and 6% of elevation.
During the exercise, the speed and elevation that you select will remain for the entire exercise until the next change you make. Your progression
in the exercise is shown by the flashing dot.
To select the Walk program:
Press the OTHER PROGRAMS key (T280P – T280C only) or the INCREASE or DECREASE key until you reach the Walk program.
Press the JustGo
TM
/ENTER key to accept and follow the instructions shown in the central information window.
Hill Climb Program
The Hill Climb program provides both a programmed hill and speed profiles. The programmed hill profile will cause the running belt to elevate and
descend at various points during your exercise. The programmed speed profile will cause the speed to change. You can change the speed and
elevation during the exercise if you find it too easy or hard.
The speed and elevation will change as you progress into the program. Changing the speed manually will cause only that segment to change.
Changing the elevation manually will cause the entire elevation profile to change.
The following table shows the different elevations for each level.
Level
Elevation %
1
0 to 3
2
1 to 4
3
2 to 6
4
3 to 7.5
5
4 to 10
To select the Hill Climb program:
Press the OTHER PROGRAMS key (T280P – T280C only) or the INCREASE or DECREASE key until you reach the Hill Climb program.
Press the JustGo
TM
/ENTER key to accept and follow the instructions shown in the central information window.
Speed Run Program
The Speed Run program like the Hill Climb program controls a certain parameter. Speed Run is speed changes. Selecting a higher level will
default a higher speed profile. Elevation changes are user controlled.
The speed will change as you progress into the program. Changing the speed or elevation manually will cause the rest of the program to change.
The following table shows the different speeds for each level.
Level
Speed (mph)
Speed (km/h)
1
1 to 4
1.6 to 6.4
2
1 to 5
1.6 to 8.1
3
2 to 6
3.2 to 9.7
4
3 to 7
4.8 to 11.3
5
4 to 8
6.4 to 12.9
To select the Speed Run program:
Press the OTHER PROGRAMS key (T280P – T280C only) or the INCREASE or DECREASE key until you reach the Speed Run program.
Press the JustGo
TM
/ENTER key to accept and follow the instructions shown in the central information window.
