background image

18

ZZAN602 can be used with a rechargeable battery when necessary. If you use 
rechargeable batteries, please follow the instructions.

RECHARGEABLE BATTERIES (NOT INCLUDED)

Prior to the use of a new unit, the rechargeable battery should be charged 
according to the battery manufacturer’s instructions. Before using the battery 
charger, read all instructions and cautionary markings on the battery and in this 
instruction manual. After being stored for 60 days or more, the batteries may 
lose their charge. After long periods of storage, batteries should be charged 
prior to use.

BATTERY CHARGING

(1)  Plug the charger into any working 110 or 220/240v mains electrical outlet. 

The use of any attachment not supplied with the charger may result in the 

risk of fire, electric shock, or injury to persons.

(2)  Follow the battery manufacturer’s instructions for charging time.
(3)  After the battery manufacturer’s recommended charging time has been 

completed, unplug the charger and remove the battery.

(4)  Batteries should always be stored in a fully charged state. To ensure 

optimum battery performance, follow these guidelines:

(a)  Although overcharging the batteries for up to 24 hours will not damage 

them, repeated overcharging may decrease useful battery life.

(b)  Always store batteries in their charged condition. After a battery has been 

discharged, recharge it as soon as possible. If the battery is storedmore than 

60 days, it mayneed to be recharged.

(c)  Do not short the terminals of the battery. This will cause the battery to get 

hot and can cause permanent damage. Avoid storing the batteries in your 

pocket or purse where the terminals may accidentally come into contact with 

coins, keys or any metal objects.

(d) WARNINGS:

1. Do not attempt to charge any other types of batteries in your charger, other 
than the nickel-cadmium rechargeable batteries. Other types of batteries may 
leak or burst.

2. Do not incinerate the rechargeable battery as it may explode!

CHAPTER 18 : BATTERY INFORMATION

Summary of Contents for ZZAN602





















Reviews: