background image

 

                                                                                   

16 

  If you are moving the map mode, click on the lower right corner of the motion map button, you 

can switch to the map mode interface, view your trajectory. 

  Finish your movement when you press the stop button, the motion show will save the record in 

your record in the history of the movement. 

 

FCC Warning 
This  device  complies  with  part  15  of  the  FCC  rules.  Operation  is  subject  to  the  following  two 
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any 
inte rference received, including interference that may cause undesired operation. 
   
Changes  or  modifications  not  expressly  approved  by  the  party  responsible  for  compliance  could 
void the user's authority to operate the equipment.   
 
NOTE: This  equipment  has been  tested  and found  to  comply  with  the  limits for  a  Class  B  digital 
device,  pursuant  to  part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide  reasonable 
protection against harmful interference in a residential installation. This equipment generates uses 
and  can  radiate  radio  frequency  energy  and,  if  not  installed  and  used  in  accordance  with  the 
instructions,  may  cause  harmful  interference  to  radio  communications.  However,  there  is  no 
guarantee that interference will not occur in a particular installation. If this equipment does cause 
harmful  interferenceto  radio  or  television  reception,  which  can  be  determined  by  turning  the 
equipment off and on, the user is encouraged to try to correct the interference by one or more of the 
following measures: 

  Reorient or relocate the receiving antenna. 

  Increase the separation between the equipment and receiver. 

  Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  the  receiver  is 

connected. 

  Consult the dealer or an experienced radio/TV technician for help. 

 
The device has been evaluated to meet general RF exposure requirement. The device can be used 
in portable exposure condition without restriction. 

Summary of Contents for HC108A


















Reviews: