background image

 

 

SX-16 Nightsun

®

 Searchlight System 

 

Maintenance Manual 

Document 031734-1/Revision A  

031734-1 Revision B 

 

January 27, 2014

 

  

 

  

 

2.2 

Safety Messages Used in this Manual 

This manual contains important safety messages that are identifiable by their appearance. These 
safety messages identify hazards and contain information to help you avoid personal injury, and 
property damage to the Searchlight, aircraft, or other property. All of these safety messages contain 
an exclamation symbol (!) surrounded by a triangle. There are three types of safety message used in 
this manual. 

 

Danger

 notices indicate a hazardous situation that will result in serious injury if not avoided. A 

danger message has the following appearance: 

 

 

Warning

  notices indicate a hazardous situation that could result in serious injury if not avoided.  A 

warning message has the following appearance: 

 

Caution

  notices indicate a hazardous situation that could result in minor or moderate injury if not 

avoided. A caution message has the following appearance: 

 

2.3 

Notice Messages 

Notice messages are also used in this manual (Figure 2-4).  These notices contain special 
instructions that are important, but they are not related to safety issues.  Notice messages have the 
following appearance: 
 

NOTICE 

This portion of the notice will contain the special information. 

 

3.0  SETUP 

This section describes  a typical SX-16 Nightsun

®

  installation. It addresses placement of the SX-16 

Nightsun

®

, safety issues, basic connections for the components, and adjustment of the Gimbal’s 

Azimuth stop. 

3.1 

Searchlight Kits 

Searchlight  kits are available from Spectrolab to accommodate many commercial and military 
helicopters. Each kit contains the hardware (mounting brackets not included) and cables. The kits are 
designed for installation by qualified airframe mechanics. 

 

 

 

 

 

Source:  Spectrolab, Inc. 

5

 

The document reference is online, please check the correspondence between the online documentation and the printed version.

Summary of Contents for SPECTROLAB SX-16 Nightsun



























Reviews: