background image

Operation

 

 
 
 

Turning extraction unit On 

The main isolation switch must be switched to the “On” 
position (Refer to section 

1

 

for switch location) by 

depressing the ‘I’ side of the switch.  
 
 
 
 
 
 
 
 

 

 

 

 
 
 
 
 

 

 

 

Setting the desired airflow 

The V600 features manual flow control. This enables the 
user to set the required airflow rate. Over time as the filters 
begin to block the user should manually increase the motor 
speed to ensure the correct flow is maintained to 
compensate for any loss in performance caused by the 
added restriction of the partially blocked filters. 
 
 

 

The extractor and all pipe work must be fully 
installed and connected before the airflow is set. 

 
 
 
 
 
 

 
To set the airflow

  

 
Press the Up arrow button to increase airflow and press the 
down arrow button to decrease airflow. The level of airflow 
is indicated by the vertical row of six blue LEDs to the right 
of the mains isolation switch. As the airflow increases, more 
blue LEDs light up and the opposite for decreasing the 
airflow. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 

 

 
 

Remote Speed Control 

If your V600 extraction unit is installed with this optional 
extra the airflow can be remotely controlled from a 
controller run from the unit on a signal cable. The airflow is 
adjusted in the same way as detailed above. 

 
 

 

 

 

 

 

01 

Increase Airflow 

 

Decrease Airflow 

Summary of Contents for V600


















Reviews: