background image

Replacement Parts  

 
 
 
 
 

Consumable Spares 
 

The V600 extraction system contains two filters. These 
should be replaced when instructed to do so by the V600 
system (see section 

6

 for replacing the filters) 

 
To maintain performance it is important that the filters are 
replaced with identical BOFA filters. To re-order please refer 
to the Filter number printed on the filter installed in your 
extraction unit. 
 
 

 
Maintenance Protocol 
 

Users can record changes in filter change intervals on the 
table below. 
 

Unit Serial Number: 

Pre Filter 

Date 

Engineer 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Combined Filter 

Date 

Engineer 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 
 
 
 
 

Filter disposal 
 

The V600 combined filter is manufactured from non-toxic 
materials. Filters are not re-usable, cleaning used filters is 
not recommended. The method of disposal of the used 
filters depends on the material deposited on them. 
 
For your guidance 
 

Deposit 

EWC 
Listing* 

Comment 

Non 
Hazardous 

15 02 03 

Can be disposed of as non-
hazardous waste.  

Hazardous  15 02 02M 

The type of hazard needs to 
be identified and the 
associated risks defined. The 
thresholds for these risks 
can then be compared with 
the amount of material in 
the filters to see if they fall 
into the hazardous category, 
if so, the filters will need to 
be disposed of in line with 
the local/national 
regulations. 

*European Waste Catalogue 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 

01 

Summary of Contents for V600


















Reviews: