background image

Page   8 

BCMC 3000 Series Master Clock Programming Manual 

50 Spring Street, P.O. Box 575, Ramsey, New Jersey  07446   Tel: 201-934-8500, Fax: 201-934-9832, Web Site: www.bogen.com 

Editing Schedule Changes 

The display will  read: 
 
 
 
 
Press the YES/ENTER button to edit a schedule change.  Press the NO/CANCEL button to 
advance to the next option. 
 
If the user selected to edit a schedule change, the display will read: 
 
 
 
 
Scroll using the 

 and 

 buttons till the schedule change that you want to edit appears on the 

display.  Press the YES/ENTER button to edit.  Follow the instructions on page 7 to set up a 
schedule change.   
 
If you wish to delete the schedule change, type in 000 over the schedule and accept the 
changes. 

Edit Schedule Change 

Sch ###     mm.dd.yy 

Edit? 

    hh:mm:ss 

The display will read: 
 
 
 
Press the YES/ENTER button to enter this option.  Press the NO/CANCEL button to leave 
programming.   
 
The display will read: 
 
 
 
Scroll through the zones using the 

 and 

 buttons.  Press the YES/ENTER button to scroll 

through the durations.  Press the NO/CANCEL button when the user is done selecting their 
preference.  The display will read: 
 
 
Press the YES/ENTER button to confirm. 

Activate Manually 

Activate Manually? 

Press NO To Exit 

Zone 001   Dur: N.A. 

Are You Sure? 

Summary of Contents for BCMC 3000 Series













Reviews: