background image

Limited Warranty

30

The UTI312 is warranted to be free from defects in material or workmanship for two (2) years from the date of sale to the original
purchaser. Any part of the product covered by this warranty that, with normal installation and use, becomes defective will be
repaired or replaced by Bogen, at our option, provided the product is shipped insured and prepaid to: Bogen Factory Service
Department, 50 Spring Street, Ramsey, NJ 07446, USA. The product will be returned to you freight prepaid. This warranty does
not extend to any of our products that have been subjected to abuse, misuse, improper storage, neglect, accident, improper
installation or have been modified or repaired or altered in any manner whatsoever, or where the serial number or date code has
been removed or defaced.

THE FOREGOING LIMITED WARRANTY IS BOGEN'S SOLE AND EXCLUSIVE WARRANTY AND THE PURCHASER'S SOLE
AND EXCLUSIVE REMEDY. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED,
AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY
DISCLAIMED AND EXCLUDED TO THE MAXIMUM EXTENT ALLOWABLE BY LAW.

Bogen's liability arising out of the

manufacture, sale or supplying of products or their use or disposition, whether based upon warranty, contract, tort or otherwise,
shall be limited to the price of the product. In no event shall Bogen be liable for special, incidental or consequential damages
(including, but not limited to, loss of profits, loss of data or loss of use damages) arising out of the manufacture, sale or supplying
of products, even if Bogen has been advised of the possibility of such damages or losses. Some States do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which vary from State to State.
Products that are out of warranty will also be repaired by the Bogen Factory Service Department -- same address as above or call
201-934-8500.  The parts and labor involved in these repairs are warranted for 90 days when repaired by the Bogen Factory
Service Department.  All shipping charges in addition to parts and labor charges will be at the owner's expense. All returns require
a Return Authorization number.

08/10/2004

Summary of Contents for UTI312

































Reviews: