background image

 

7

4)

 

Inspection of proper fastening of the RIP, tightening of contacts, and wire integrity; 

5)

 

Replacing the batteries when necessary but at least once per 5 years. 

4

 

MANUFACTURER WARRANTY 

4.1

 

The manufacturer guarantees that the RIP meets technical requirements specified in 

the manuals if the user follows the instructions for shipment, storage, installation, and usage. 

4.2

 

Warranty period is 18 months but no more than 24 months from the manufacturer's 

date of issue. 

4.3

 

In  case  of  any  issue  related  to  setting  and  use  of  the  product,  please  contact  the 

technical support: +7 (495) 775-71-55 or e-mail: 

support@bolid.ru

4.4

 

When  submitting  the  product  for  repair,  it  shall  be  accompanied  with  descriptions 

of possible fault. 

Claims shall be submitted to the following address: 
NVP BOLID CJSC, Pionerskaya #4, Korolyov city, Moscow region, Russia, 141070. 
Phone/fax: (495) 775-71-55 (multiline), 516-93-72. 

E-mail: 

info@bolid.ru

; Support :

 

support@bolid.ru

 

http://bolid.ru

.

 

5

 

CERTIFICATES 

5.1

 

Battery  Backed  Power  Supply  RIP-24  model  01  (RIP-24-3/7M4)  meets  the 

requirements  of  technical  regulations  of  the  Custom  Union  TR CU 004/2011; 
TR CU 020/2011. Approved by Conformity Certificate 

 RU 

С

-RU.

МЕ

61.

В

01270. 

5.2

 

Manufacture  of  RIP-24  model  01  (RIP-24-3/7M4)  is  approved  by  Conformity 

Certificate GOST R ISO 9001-2015 

 

РОСС

 RU.

АБ

66.

К

00003. 

Summary of Contents for RIP-24









Reviews: