background image

52

Switching on/off

1.  Connect the appliance to a properly installed earthed plug 

socket. A beep of moderate length will sound when the appli

-

ance has been correctly assembled. 

2.  Switch the appliance on using the POWER   button. Keep 

the button pressed until you hear a short beep. The display 

lights up. You will see the start display SPEED “0000” and 

“[00:00]” for the timer. The appliance is ready for use.

3.  You can start and stop operation of the appliance by briefly 

pressing the POWER   button.

4.  If you want to end operation, keep the POWER   button 

pressed, until the illuminated display goes out. Disconnect the 

mains plug from the socket.

Pausing operation

•  Press the POWER

 

 button briefly once, the running time / 

 

remaining running time, the set speed and temperature 

 

remains on the display. If you want to continue operation, 

briefly press the POWER   button again.

•  The motor has several safety switches. They switch the 

 

motor off as soon as one of them is opened. 

-  If the arm (1) is tilted upwards, the program status is 

retained. To continue operation of the appliance, lower 

the arm until it audibly clicks into place and then press the 

POWER   button. 

-  If operation is paused, detach the bowl as well. You will 

hear a longer beep. The program status is retained, even 

if the timer display goes out. After the bowl has been at

-

tached properly and the arm has been lowered, press the 

POWER   button, to continue operation with the previ

-

ous settings.

-  During operation, opening the blender motor cover or 

detaching the blender jug, immediately switches the 

appliance off. The display goes out. The program status 

is cleared. The power supply is interrupted. The appli

-

ance restores the default setting (speed setting 1). If you 

want to continue operation, switch the appliance on and 

change your settings.

Indicators on the Display

The indicators on the display depend on the operating mode.

•  The speed setting is shown next to SPEED when the ap

-

pliance is used as a kneading/mixing machine, blender or 

mincer.

•  If used as a cooking appliance, the current temperature (in 

°C) will be shown next to TEMP instead of the speed setting.

•  The TIME indicator informs you of 

a)  the operating duration

b)  the remaining running time of the set program, if you have 

activated the timer with the   button.

•  If you have activated the timer or/and set a temperature, you 

can access your previously selected settings with the 

 but-

ton. Press the button three times. The following indicators are 

each displayed for three seconds in the following sequence:

1.  Speed setting SPEED

2.  Time TIME

3.  Temperature TEMP.

•  The illuminated display goes out if the appliance is not in use 

and no button has been pressed for approx 10 minutes. The 

program status is retained. Press any button (except

  

POWER  ) to switch the display on again. Check your 

 

previous settings with the   button.

Speed settings

•  Speed setting 1 is the default setting after the appliance is 

connected to the mains.

•  If the appliance is switched off without disconnecting the 

mains plug from the socket or removing the cover for the 

blender motor/blender jug, the last selected speed setting will 

be saved. 

•  The appliance has 11 speed settings (1 to 10 and -1), which 

can be selected with the buttons 

 /  .

  Setting 

1  =  low speed

  Setting 

10  =  top speed

  Setting 

-1  =  slowest speed for stirring when cooking

•  When using as a cooking appliance, you can only select set

-

tings above speed setting 1 if the temperature has not yet risen 

to 60°C. 

 

Speed settings -2 and -3 represent the intervals at which the 

food is stirred at speed setting -1 during cooking.

  Setting 

-2  =  short intervals

  Setting 

-3  =  long intervals

  If you want to switch from setting -3 to setting -2 or -1, use the 

 button.

Timer (electronic timing device)

If you want to limit the operating time, proceed as follows:

•  Press the   button once.

•  Use the 

 / 

 buttons to select between 1 and 60 minutes.

•  If you do not press another button within a few seconds, the 

display changes to “00:00”. Your settings are retained how

-

ever.

•  You can also reset the timer during operation using the 

 

and 

 / 

 buttons, without interrupting the program. The 

previous operating time is retained.

Temperature

To use as a cooking appliance, select a temperature of between 

25°C and 140°C.

•  Press the   button twice.

•  Use the 

 / 

 buttons to select the temperature. 

•  If you do not press another button within a few seconds, the 

display will change to show the current temperature. Your 

settings are retained however.

•  You can also reset the temperature during operation using the 

 and 

 / 

 buttons, without interrupting the program.

Clear with the   button 

•  If you want to clear the set Timer after the program has 

started:

1.  Interrupt the program with the POWER   button. 

2.  Press the   button repeatedly until you get to the timer 

setting.

Summary of Contents for Cook & Mix KM 379 CB































































Reviews: