19
•
Determine the position of the cooker hood central-
ly above the cooking area in accordance with the
specified safety distances.
Totally 6x mounting holes with a diameter of approx.
8 mm are necessary for the wall mounting. Insert the
supplied dowels
(Fig. 1).
(Fig. 1).
(Fig. 1).
(Fig. 1).
•
First mark the holes required for fixing the hood
body in accordance with the supplied drilling tem-
plate. Check the markings with a water balance
and make the holes.
-
Turn in the upper screws 2x ST4*30mm for the
suspension of the hood body so far that they
project approx. 5 mm out of the wall.
•
Fasten the bracket for the upper shaft termination
with the screws 2x ST4*40mm after determining
the extension length of the shaft cover.
•
Before attaching the hood
(Fig.
(Fig.
(Fig.
(Fig. 2)
2)
2)
2)
:
-
Fasten the glass screen with the screws
4x M4*20mm in the screw insert made of rub-
ber together with washers on the hood body.
-
Affix the connecting piece with inserted non-
return valves from the top of the extraction
duct with the screws 2x ST4*8mm.
Insert the two non-return valves by lightly
bending them from above into the connecting
piece
(Fig. 2a)
(Fig. 2a)
(Fig. 2a)
(Fig. 2a)
.
For the exhaust
For the exhaust
For the exhaust
For the exhaust hose:
hose:
hose:
hose:
Hereupon a flexible exhaust
hose (supplied) with an inner diameter of 150 mm
must be attached. Secure the hose with the cable tie.
•
Hang up the hood. Check the secure hold and the
horizontal position. Tighten the lower screws 2x
ST4*30mm through the hood body to secure the
hood
(Fig. 3)
(Fig. 3)
(Fig. 3)
(Fig. 3)
.
For the exhaust hose:
For the exhaust hose:
For the exhaust hose:
For the exhaust hose:
Check the correct position of
the exhaust hose and connect it with the outlet open-
ing.
•
Fit the telescoping shaft unit. Pull up the inner
shaft and fix the shaft cover to the side of the
bracket using the self-tapping screws 2x
ST4*8mm
(Fig. 4
(Fig. 4
(Fig. 4
(Fig. 4))))
.
Installing the activated carbon
Installing the activated carbon
Installing the activated carbon
Installing the activated carbon filter for recirculation
filter for recirculation
filter for recirculation
filter for recirculation
mode
mode
mode
mode
•
Remove the aluminum grease filter (see “Clean-
ing the aluminum grease filter).
•
Place the carbon filter onto the intake of the ex-
haust air duct. Make sure that the fixing pins of
the carbon filter engage in the fastening slots of
the exhaust air duct. Put the filter in A
A
A
A and press
firmly flat B
BB
B.
•
Reinstall the aluminum grease filter.
Electrical connection
Electrical connection
Electrical connection
Electrical connection
WARNING:
WARNING:
WARNING:
WARNING:
•
The installation to the mains supply must conform
to the local standards and regulations.
•
Improper connection may cause to an electric
electric
electric
electric
shock
shock
shock
shock!
•
Do not modify the appliance plug. If the plug does
not fit properly to the outlet, let install a proper
outlet by an authorized specialist.
•
The accessibility of the power plug must be en-
sured to disconnect the appliance from the power
supply in case of emergency.
•
Ensure that your mains power corresponds with
the specifications of the appliance. The specifica-
tions are printed on the rating label.
•
Connect the mains cable to a properly installed
and earthed wall outlet.
•
If the plug after installation is not accessible, a
corresponding disconnect device must be availa-
ble to meet the relevant safety regulations.