32
UM1354CB_IM_new
17.03.17
Installation
Mains Lead
Remove the mains lead from the storage compartment in the
bottom section.
Mixing Vessel
1. Check any preassembled parts! (Fig. A + B) The safety
disc (4), sealing ring (5), blade block (6) and screw top (7)
must be assembled in the correct order.
CAUTION:
• Do not forget to insert the sealing ring as otherwise
the carafe will leak.
• Always place the sealing ring on the blade block.
• The screw top must be straight when screwed into
place.
• The three guide mechanisms of the safety disc must
lie in the recesses of the screw top.
2. Place the carafe on the motor housing (8) (Fig. C). You
can select whether the handle of the carafe should point
to the left or right.
NOTE:
When the carafe is placed in position the assembled
safety disc presses on the safety switch of the motor
housing. If incorrectly installed the mixer cannot be
operated.
Notes on Use
• Please clean the mixer vessel, the lid and seal before ini
tial use in warm soapy water.
• Please cut the items that are to be mixed into small piec
es beforehand.
•
Ingredients:
Do not put any hot items into the mixing
vessel.
•
Seal:
The seal can also be used as a measuring jug (full
to the brim = 50 ml).
•
Short-term operation:
The device is suitable for short
term operation of not more than 1 minute. After this time it
should be switched off.
•
Pulse operation:
Pulse mode is turned on by turning
the switch to the “
P
” position and releasing it again. The
device should not be used in this mode for more than
1 minute. Allow it to cool down for 2 minutes before using
it again!
•
Chopping up Ice Cubes:
The blade in the mixing vessel
is also suitable for chopping up ice cubes. Please only fill
the carafe up to 1/3 full with ice cubes. Only pulse mode
“
P
” should be used for chopping up ice cubes.
Operation
Electrical Connection
Check whether the electrical voltage that you intend to use is
the same as that of the machine. Details are to be found on
the label on the base.
Preparation
• Ensure that the function switch (9) is in the “
0
” position.
• Place the mixing vessel in position.
• Now put the ingredients that are to be mixed into the mix
ing vessel (max. 1.5 litres).
• Press the lid (2) tightly onto the carafe (Fig. D). It must
tightly seal the mixer vessel.
• Close the lid with the seal (1) (Fig. E). Note the recesses
on the inside of the lid. Turn the seal tight in a clockwise
direction.
• Connect the mains lead to a properly installed safety pow
er socket. The switch ring (10) lights up.
•
Please hold the carafe firmly during mixing.
Mixing
•
For constant mixing (continuous mode):
If the device is operated on levels 1 and 2 the switch locks
in place in the respective position.
Level 1 = low rpm
Level 2 = high rpm
Shift the selector to “
0
” to switch off the appliance.
3.
For pulse mode (mixing at brief intervals):
Move the switch to the “
0
” position. The switch snaps
into place. The appliance is off now. Turn the switch now
to position “
P
”. The switch must be kept in this position
for the desired interval. When the switch is released, it
returns automatically to “
0
” position.
Adding further ingredients to be mixed
Please switch off the machine before doing so. Spices
or other ingredients that are to be mixed can be inserted
through the hole in the seal.
Stopping Operation
• Turn the switch to the “
0
” position.
• Remove the mains plug from the socket. The illumination
goes off.
• Remove the mixing vessel.
• Take off the lid before pouring.
IMPORTANT NOTE:
Citrus juices and food containing acids should never be
stored in metal vessels.
• The mains lead can be stored in the bottom section.
Summary of Contents for UM 1354 CB
Page 55: ......
Page 56: ......
Page 57: ......
Page 58: ...UM 1354 CB UM1354CB_IM_new 17 03 17 Stand 03 2017 Made in P R C ...
