Warnings
The AntennaJet AAS300DP is a Antenna Splitter and may only be operated according to regulations. It is
for receive only and
NOT for transmit
. Please, pay attention to the following warnings. Noncompliance can
lead to serious damage of the AntannaJet AAS300DP
Never connect the antenna terminal to a transmitter or a transceiver!
Never open the cover! This could lead to a short circuit or even to a fire!
Ambient conditions
The AntennaJet AAS300DP can be operated at temperatures ranging from 5 °C to 40° C and at a relative
humidity from 20 - 80 percent ( non-condensing)
When switched off, the AntennaJet AAS300DP can be stored from 0 °C- 60°C
In case of a thunderstorm, disconnect the AntennaJet AAS300DP from the USB port and disconnect the
antenna.
Before using the AntennaJet AAS300DP have the splitter adapted to the ambient temperature. Large
difference in temperatures and humidity can lead to condensation, which in return may cause a short
circuit.
Keep the original box in case the splitter has to be sent in.
Correct use
With the AntennaJet AAS300DP you can receive radio frequencies, evaluate signals, filter signals etc.
In case of non-intended use, any liability is excluded.
Individual modifications are prohibited.
This splitter is only intended for use in dry interiors.
This device contains electrical parts. It may be damaged in case of heavy impact or fall.
This splitter is exclusively intended for private use and not for commercial or industrial purposes. The
usage under extreme conditions may lead to damage.
Run the cables in such a way that no one can step on them or trip over them
Do not put any items on the cables because they may be damaged
COMPLIANCE FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference. 2. This device must accept any interference received,
including interference that may cause undesired operation.
Note:
This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
Warning:
Any
modifications
made
to
this
device
not
expressly
approved by Bonito in Germany could void the user’s authority to operate the equipment.
Gerichtsweg 3; 29320 Hermannsburg; Germany
E-Mail: office@bonito.net; Web: www.bonito.net
Thank you for purchasing this product Bonito. This little guide should help you get started. We
hope you enjoy using this product Bonito. This manual contains important instructions for the
use of Bonito AntennaJet AAS300DP. Please read the instructions carefully before use it.
Product contents
Please, check the completeness of the shipment and notify us within 7 days after purchase if it
was not complete. In this product is included:
Bonito AntennaJet AAS300DP
Documentation
Product contents
USB Cable with ferrite
Plug power adaptor 9 Volts DC
MB Mounting bracket
Introduction
The Bonito AntennaJet AAS300DP is a 3-Way antenna splitter and is splitting the signal from
one RX antenna to 3 different receivers simultaneous.
Connections
The following picture shows the terminal assignment:
1x BNC 50 Ohm RF-Input
3x BNC 50 Ohm RF-Output
1x USB B female for 5 Volt power supply
1x DC power jack - Connects to a 5-12VDC power source using a center-positive, 5.5/2.1mm
barrel connector.
www.bonito.net
Important
The AAS300DP can be powered via a 5-12 VDC power source. Whenever possible, don’t
use a switching power supply but a transformer. Power can also be supplied by USB.
Don’t use the different sources at the same time!
