Bonnet P072188 Manufacturer'S Instructions Download

Page: 17 / 17

Page 16

BONNET CIDELCEM GRANDE CUISINE
Siége social:

Rue des Frères Lumière - Z.I Mitry Compans
77292 MITRY MORY Cedex

3. INSTALLATION: CONNECTION

3.1 ELECTRICAL CONNECTION

Earth bonding point

Whatever the model the electrical connection is at the rear.

- Remove the cover
- Feed cable through cable gland and tighten
- Connect up wires
- Connect earth to bonding point provided.
- Replace cover.

IMPORTANT:

Only use power supply cables of H07 RNF type with section as indicated below:

Voltage

Cable

380 / 415

5 x 2.5 mm

Provide suitable multipolar isolator (with a contact opening distance of at least 3 mm).
The installation must comply with current electrical regulations (France NFC 15.100).

The appliance must be earthed

The various electric appliances must also

be earth bonded

(every metal part on the same voltage) via the terminal provided located next to connection cord-grip.

The manufacturer can not be held responsible in case of failure to heed these

instructions.

Summary of Contents for P072188


















Search results

Summary of Contents for P072188

Reviews:

Related manuals for P072188

Brands by name

Popular brands

Bonnet P072188, Manufacturer'S Instructions

Search results

Summary of Contents for P072188

Reviews:

Related manuals for P072188

Brands by name

Popular brands